Cardin Elettronica SL Série Manuel D'instructions page 20

REMOTE CONTROL (fig. 3 page 4)
The system can be remotely activated using radio control devices.
Each channel can be set to a maximum of 2 functions:
- function 1: sequential command
- function 2: limited opening or blocking button
To set one of the functions to the channels A-B-C-D use the selection
J1
A
B
1
2
close-block open-close
Memory module (M1)
This is extractable, furnished with a non volatile EEPROM type memory
and contains the transmitter codes and allows you to memorise up
to 300 codes. The programmed codes are maintained in this module
even during blackouts. Before memorising the transmitters for the first
time remember to cancel the entire memory content. If the electronic
card has to be replaced due to failure, the module can be extracted
from it and inserted into the new card. Make sure that the module is
correctly inserted as shown in fig. 3.
Signal LEDs "L3" (fig. 3):
Flashing quickly: cancels a single code
Flashing slowly: memorises a single code
Permanently lit: memory full.
TRANSMITTER CODE MANAGEMENT
Memorising a channel (fig. 3):
slowly.
2. At the same time activate the transmitter which is to be memo-
rised.
P1 MEMO
again.
4. Release the button: The LED will continue to flash.
5. Activate the transmitter again (same transmitter, same channel; if the
channel is different or it is a different transmitter the memorisation
attempt will abort without success).
indicating that the transmitter has been correctly memorised.
Note: It is not possible to memorise a code which is already in memory:
if you attempt this, the LED will switch off when you activate the trans-
be able to continue the memorising procedure.
If after activating the transmitter for the first time you wait for more
than fifteen seconds without activating the transmitter a second time
the memorisation attempt will abort without success.
Cancelling a channel (fig. 3):
flash quickly.
2. Activate the transmitter channel which is to be cancelled.
3. The LED will remain lit for 2 s, indicating that the transmitter has
been cancelled.
Note: If the user that you wish to cancel is not in memory, the LED
to continue the cancellation procedure.
For both the memorisation and cancellation procedures, if the button
is released before activating the transmitter the procedure will abort.
Cancelling all user codes from memory (fig. 3):
seconds.
L3
seconds).
L3
nated.
TD;
TAL or TB.
J3
TB;
TAL;
1 open-block-
P1 MEMO L3
L3
L3
P1 MEMO will you
P2 L3
P2
P1+P2
Note: When the memory is almost full the time required to search for
a user code could take up to 1 second from when the command was
received. If led "L3" remains lit memory is completely full. To memorise
a new transmitter you will first have to cancel a code from memory.
Memorising ulterior channels via radio
J2
2. Using a transmitter, in which at least one
been memorised in the receiver, press
the button in the transmitter as shown
in the figure.
Note: all the receivers within range when the channel button is pressed
(and which have at least one of the transmitter channel buttons memo-
3. Press one of the channel buttons on the same transmitter. The
receivers which do not contain that channel code will sound a five-
programming via radio" mode.
4. Press the previously chosen channel buttons on the transmitter
half a second each after which the receiver will be ready to receive
another code.
5. To leave the programming mode wait for 3 seconds without pressing
will then exit the programming mode.
Note: When the memory is entirely occupied the buzzer will sound
radio
L3
via radio
CONNECTING THE ANTENNA
Connect an ANS400 tuned antenna using a coaxial cable RG58
(impedance 50 ) with a maximum length of 15 m.
FUNCTION MODE
1) Automatic
When the door is completely closed the opening command will start a
complete cycle which will end with automatic reclosing and the night
light switching off.
Automatic reclosing starts after the programmed pause period has
elapsed when the opening cycle has been completed or straight
away after the intervention of a photoelectric cell (the intervention of
a photoelectric cell causes the pause time to be reset).
During the pause time the symbol
pressing the blocking button during this period will stop automatic
reclosing and consequently stop the display from flashing.
The indicator light remains lit until the closing manoeuvre has termi-
nated.
2) Semiautomatic
Work cycle control using separate opening and closing commands.
When the door has reached the completely open position the system
will wait until it receives a closing command either via an external control
button or via radio control, before completing the cycle.
The indicator light remains lit until the closing manoeuvre has termi-
nated.
3) Manual manoeuvre
This can be used to close the gate (or open it) under the direct control
This mode is only active after you have programmed the system. In
-
this mode the safety devices FTCI, CSP and TB only work when they
are in alarm.
20
J2
B1
programming via
programming
2
will flash on the display and
2
9 ON
ON
OFF