Castor Plates; Amputee Axle Plate; Backrests - Sunrise Medical QUICKIE Classic 100 Notice D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

Options – Castor Plates
Seat height and seat angle adjust-
ment
Remove the nut (1) and the axle from
the castor adapter (2). To adjust the
seat height to configure the spacers (4)
according the seat height matrix.
Finally position the collar (3) to the
desired chair tilt, taking
NOTE of the notches located on the
top side (Fig. 2).
Angle setting 1 = 3° (rear of chair)
Angle setting 2 = 0°
Angle setting 3 = 6° (front of chair)
Adjust the collar in such a way that the
axle is as close to perpendicular to the
ground as possible. When finished,
make sure that all scrwes have been
correctly tightened (see the page on
torque).
Horizontal Axle Position
The axle plate can be positioned
forward for maximum maneuver-
ability or rearward for increased
stability.
CAUTION:
Wheel locks must be adjusted to
suit the new position.
The longer the wheel base, the
greater the stability of the
wheelchair. Turn the axle bracket
to the rear (1) in order to extend
the wheel base.
CAUTION:
Wheel locks must be adjusted to
suit the new position.
Options – Amputee Axle Plate
Amputee Axle Bracket
With the amputee support (accessory) the wheel
base can be extended by 10,5 cm. When you have
completed the adjustment, make sure that all
screws have been properly tightened (see the page
on torque).
CAUTION:
Wheel locks must be adjusted to suit the new
position.
8
CLASSIC 100, 160, 160XL
1
2
4
3
Options – Backrest
Height adjustable backrest
The backrest height can be adjust-
ed to 5 different positions (38–40
cm). Open and remove the bolt (1)
and move the back tube into the
desired position. Then fix the bolt
again.
Angle-Adjustable backrests
The backrest can be adjusted to 5
different positions (3° forward, 0°,
5°, 10° and 15° backwards). A nut
(1) is located on the backtube,
allowing you to set the angle.
Angle adjustment of the back post
will require adjustment of the arm-
rest „hook" support.
CAUTION:
The screws (1) connect the
backrest directly to the frame;
always ensure they are tightened correctly.
Screws that are too loose can be easily lost. In
either case, injuries could result when using the
push handles to ascend stairs.
For your own safety, we recommend that adjust-
ments only be made by authorized dealers.
The back rest height as well as the height of the
pivot point can be adjusted.
Half folding backrest
For folding the back down slight up the
lock.
CAUTION:
Make sure that the backrest locks in cor-
rectly when it is set upright again.
Reclining back (8°-40°/50°)
By pulling the 2 levers (1) at the same time
the backrest is released and can be set to
the desired position.
Releasing the 2 levers (1) will lock
the backrest automatically in the
new position. To bring the backrest
back in the upright position, just
move it (no release necessary) to
the required position.
CAUTION:
The reclining back is only
allowed to be used in combi-
nation with rear wheel
extension.
CAUTION:
The reclining back is recommended to be used
in combination with active anti-tips (max ground
clearance 3-5 cm)
CAUTION:
The reclining back is recommended to be used
in combination with a stabilizer bar.
1
2
1
1
1
1009/3/ST-000690634.EMS.2/Rev.D

Publicité

Table des Matières
loading

Table des Matières