Treatment Of Underarm Perspiration - KaWe SwiSto3 Mode D'emploi

much of the surface of the body part to be treated as possible rests on
the electrodes and the pressure is uniformly distributed. The parame-
ters that can be selected blink on the display. The current intensity for
the treatment can be selected with the UP and DOWN buttons. -->
Confirm selection by pressing the SET button. --> Select pulsing cur-
rent with the UP button and continuous current with the DOWN but-
ton. --> Confirm selection by pressing the SET button. --> Set the
treatment time in minutes (MIN) using the UP and DOWN buttons.
--> Confirm selection by pressing the SET button. --> Set the treat-
ment time in seconds (SEC) using the UP and DOWN buttons. -->
Confirm selection by pressing the SET button. --> Setting selection is
completed when the treatment starts, the time countdown begins and
the clock symbol begins to blink. To begin the treatment, complete the
electric circuit by putting your hands or feet into the water trays.
• By pressing the button on the membrane keypad on the upper
side of the device the treatment current can be increased until a
mild to strong tingling can be felt. The intensity of the current can be
seen on the display. Similarly, the current can also be reduced dur-
ing the treatment by pressing the
being changed during the treatment, the current reading on the
display does not blink.
• The treatment stops automatically after the set treatment time has
been reached or when the current circuit is broken before the set
time has elapsed. The treatment will resume for the remainder of
the set treatment time when the current circuit has once again been
closed. The clock symbol
sumes.
• If the clock showing the treatment time
00:00 and the current circuit is still complete, the + / - symbols on
the display both begin to blink. Once the set treatment time has
expired, none of the settings can be changed until the circuit has
been interrupted by removing the hands or feet from the water
trays. The + / - symbols then stop blinking and the MIN symbol
begins to blink, signaling that new settings can now be selected.
The previously set treatment time will be saved.
• Turn the SwiSto3 iontophoresis device off after completing treat-
ment by pressing the power button
off automatically after two minutes.
• The last-used treatment settings are automatically saved and used
when the device is restarted for the next treatment. These settings
can be changed with an open current circuit as described in Section
9.
• The SwiSto3 iontophoresis device can also be plugged into the local
power supply network to be charged using the charging plug. The
battery symbol shows the battery charge up in the top right-
hand corner of the display.
• The charging symbol appears when the charging plug is
plugged in. After testing the rechargeable battery for at most one
minute, the charging function begins and the battery symbol
begins to blink.
• When the charging plug is plugged in, the treatment is interrupted.
button. When the current is
blinks and the time countdown re-
has run down to
. The device will also turn

10. Treatment of underarm perspiration

• Prepare device for use as described in Section 8 "Start-up/prepara-
tion".
• Power-on the device by pressing the power button
second.
• For the underarm perspiration treatment, wet the sponge pock-
ets evenly with tap water. In order to avoid the occurrence of
current densities that are too high on isolated spots on the body
however, ensure that as large a contact surface as possible is touch-
ing the electrodes with a pressure distribution that is as uniform as
possible.
• Insert the plate electrodes (REF 05.19080.021) into the sponge
pockets.
• The parameters that can be selected blink on the display. The cur-
rent intensity for the treatment can be selected with the UP and
DOWN buttons. --> Confirm selection by pressing the SET button.
--> Select pulsing current with the UP button and continuous cur-
rent with the DOWN button. --> Confirm selection by pressing the
SET button. --> Set the treatment time in minutes (MIN) using the
UP and DOWN buttons. --> Confirm selection by pressing the SET
button. --> Set the treatment time in seconds (SEC) using the UP
and DOWN buttons. --> Confirm selection by pressing the SET but-
ton. --> Setting selection is completed when the treatment starts,
the time countdown begins and the clock symbol begins to blink. To
begin the treatment, complete the electric circuit by placing the
sponge pockets with the plate electrodes in them under your arm-
pits.
• Raise the upper arm and place the sponge pocket on the armpit.
• The sponge pocket is then held in place by pressing the upper arm
down against the body. Before lowering your upper arm ensure that
the electrodes and connector cables are inserted completely into
the sponge pockets, as direct contact between the metal and the
skin could cause localised burns. Especially when performing an
underarm perspiration treatment, ensure that the pressure exerted
by the upper arm remains as constant as possible for the entire du-
ration of the treatment – which can be up to 30 minutes.
• By pressing the button on the membrane keypad on the upper
side of the device the treatment current can be increased until a
mild to strong tingling can be felt. The intensity of the current can be
seen on the display. Similarly, the current can also be reduced dur-
ing the treatment by pressing the
being changed during the treatment, the current reading on the
display does not blink. WARNING: Do not exceed the recommended
maximum current intensity of 5 mA.
• The treatment stops automatically after the set treatment time
has been reached 00:00 or when the circuit is broken before the set
time has elapsed. The treatment will resume for the remainder of
the set treatment time when the circuit has once again been closed.
• If the clock showing the treatment time
20
for one
button. When the current is
has run down to 00:00