Dörr RL-48 Notice D'utilisation page 8

05 | NOMENCLATURE
1 LED ring light
2
Spiral cable ring light
3 Switch for LEDs
4 Control unit
5
Connection socket ring light OUTPUT
6 Connection socket AC adapter DC 3 V IN
7
LED indicator
8 Main switch OFF, DC 3 V = operation with AC adapter,
BATT = operation with batteries
9
Hot shoe with locking screw + ¼" tripod screw
10 Battery compartment/battery compartment cover
11
Adapter rings
12 AC adapter
13 Diffuser orange
14
Diffuser white
06 | OPERATION
Connect the spiral cable (2) with the connection socket (5) OUTPUT of
the control unit.
06.1 INSERTING THE BATTERIES
The LED ring light can be operated by 2 AA Mignon 1,5 V or by rechargeable
batteries of the same type (both optional).
1. Remove the battery compartment cover (10) of the control unit by
sliding it off.
2. Insert 2 fresh batteries or rechargeable batteries. Please respect the
polarity as indicated in the battery compartment.
3. Close the battery compartment.
4. Move the main switch (8) to BATT for operation with batteries.
06.2 OPERATION WITH AC ADAPTER
1. Connect the AC adapter (12) with the connection socket (6) DC 3 V IN
2. Connect the AC adapter with a 220 V power outlet.
3. Move the main switch (8) to DC 3 V for operation with AC adapter.
4. The LED indicator (7) lights up while in operation with AC adapter.
Note
When the AC adapter is plugged into the control unit, the power supply of
the batteries is interrupted automatically, even when the on/off switch is
in position BATT. Remove the batteries, when using the ring light with
AC adapter.
06.3 MOUNTING ON THE CAMERA/LENS
06.3.1 CONTROL UNIT
Slide the hot shoe adapter of the control unit (9) on to your cameras hot
shoe and screw the locking screw down. If your camera does not boast of a
hot shoe, you can use an optional accessory rail to mount the unit.
06.3.2 LED RING LIGHT
To mount the LED ring light (1), first mount an adapter ring (11) that suits
with the filter mount of your lens. Slide the LED ring light with its rear side
onto the adapter ring until it clicks closed. The ring light is now firmly at-
tached to your lens; however, it can still be levelled by turning it. Choose
the desired diffuser (13+14), and place the connectors over the ring light
brackets. Turn the diffuser (13+14) clockwise until secured.
07 | USAGE
1. Switch your camera on after having attached the ring light.
2. Turn the ring light on by moving the main switch (8) to position BATT
for operation with batteries or to DC 3 V for operation with AC adapter.
07.1 LED EFFECT SETTING
With switch (3) choose out from below settings:
Switch position left: 24 x LEDs on the left side are illuminated
•
Switch position right: 24 x LEDs on the right side are illuminated
•
Switch position middle: all 48 LED are illuminated
•
07.2 CAMERA SETTINGS
White Balance: Set your camera to auto white balance mode (AWB). If a
•
more accurate setting is required, you can do a manual white balance
metering (PRE).
Exposure: For macro and close-up shots we recommend to select the
•
aperture manually in order to keep the control of the depth of focus.
Adjust the shutter speed manually (M) or with aperture-priority mode (A).
Focus: We recommend manual focus adjustment for close-up and macro
•
shots.
NOTE
In order to avoid blurred images, we recommend the use of a tripod.
08 | CLEANING AND STORAGE
Never use aggressive cleansing agents or benzine to clean the device.
We recommend a soft, slightly damp microfiber cloth to clean the outer
parts of the device. Make sure to take off the device from power before
cleaning! Store the device in a dust-free, dry and cool place. This device is
not a toy – keep it out of reach of children. Keep away from pets.
08