Bosch PCM 8 SD Notice Originale page 28

28 | English
Sliding mitre saw
Divergence of laser line
Weight according to EPTA-Pro-
cedure 01:2014
Dimensions of suitable saw blades
Saw blade diameter
Base blade thickness
Max. cutting width
Hole diameter
Permitted workpiece dimensions (maximum/minimum): (see "Per-
missible workpiece dimensions", page 31)
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise information
Noise emission values determined according to EN
62841-3-9.
Typically the A-weighted noise level of the power tool is:
Sound pressure level 93 dB(A); sound power level 106
dB(A). Uncertainty K = 3 dB.
Wear hearing protection
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
See the list of items included at the start of
the operating manual.
1 609 92A 4M8 | (04.12.2018)
Check to ensure that all the parts listed below have been
PCM 8 SD
supplied before using the power tool for the first time:
PCM 800 SD
– Sliding mitre saw with mounted saw blade
mrad 1.0
– Dust bag (53)
(full
angle)
– Stationary saw table extension (11) (2 x),
fastening screws (51) (2 x)
kg 15.5
– Flexible saw table extension (63) (2 x)
– Quick-action clamp (22)
– Hex key (49)
mm 216
Note: Check the power tool for possible damage.
mm 1.4−1.8
Before continuing to use the power tool, carefully check that
mm 2
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
mm 30
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Fitting individual components
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
Fitting stationary saw table extensions (see figure A)
The stationary saw table extensions (11) with the fastening
screws (51) must be screwed to the power tool on the left
and right of the saw table (21).
– Tilt the saw table extension (11) backwards slightly and
place it in the groove of the opening (52) on the power
tool, turn the saw table extension forwards horizontally in
the groove and then press the saw table extension fully
downwards.
– Tighten the fastening screws (51) with the hex key (49)
provided.
Stationary or flexible mounting
To ensure safe handling, the power tool must be
u
mounted on a flat, stable work surface (e.g. work
bench) before use.
Mounting on a work surface (see figure B)
– Use suitable screw fasteners to secure the power tool to
the work surface. Use the holes (20) to do this.
Flexible installation (not recommended) (see figure C)
If, in exceptional circumstances, it is not possible to mount
the power tool on a flat and stable work surface, you can im-
provise by setting it up with the tilt protector.
Without the tilt protector, the power tool will not be
u
stable and can tip over especially when sawing max-
imum mitre and/or bevel angles.
– Rotate the tilt protector (15) inwards or outwards until
the power tool is positioned straight on the work surface.
Bosch Power Tools