Ryobi EWS-1266 Manuel D'utilisation page 17

GB
F D
PARTICULAR REQUIREMENTS FOR
CIRCULAR SAWS
Adjust the riving knife as described in this
■
instruction manual . Incorrect spacing, positioning
and alignment can make the riving knife ineffective in
preventing kickback.
Always use the riving knife except when plunge
■
cutting. Riving knife must be replaced after plunge
cutting. Riving knife causes interference during
plunge cutting and can create kickback.
For the riving knife to work, it must be engaged in
■
the workpiece. The riving knife is ineffective in
preventing kickback during short cuts.
Do not operate the saw if riving knife is bent. Even
■
a light interference can slow the closing rate of a
guard.
DESCRIPTION
1. Spindle lock button
2. Hex-head bolt
3. Spanner
4. Outer blade washer
5. Lower guard
6. Lower guard lever
7. Upper guard
8. Blade
9. Inner blade washer
10. Dust nozzle
11. Riving knife
12. Depth lock knob
13. Base plate
SPECIFICATIONS
Voltage
Input
No load speed
Bore size
Blade size
Cutting capacity
at 0 0
at 45 0
Bevel scale
Cord length
E I P NL
14. Depth of cut
15. Depth scale
16. Bevel adjustment knob
17. Bevel scale
18. Trigger switch
19. Safety button
20. Line guide
21. Depth adjustment lug
22. Live Tool indicator
23. Laser guide button
24. Laser guide
25. LED button
26. LED light
Blade diameter
EWS-1266 EWS-1366
230V 110V/230V
1,250 W 1,250 W/1,350 W
4,500 min -1 4,500 min
16 mm 16 mm
190mm 190 mm
66 mm 66 mm
38 mm 38 mm
0 – 45° 0 – 45°
4 m 3m/4 m
S DK N FIN GR
English
INSTRUCTIONS FOR SAFE HANDLING
The maximum permissible system impedance:
Zmax for EWS-1266 is 0.245 Zref & Zmax for EWS-1366 is
0.252 Zref.
If in doubt, please verify with your local energy-utilitythat the
AC outlets in your area do not exceed theabobe values.
STANDARD ACCESSORIES
Saw blade, Parallel fence, Spanner.
APPLICATION
Sawing wood.
NOISE BUILD-UP
Noise (sound pressure level) in the workplace can
exceed 85 dB. In this case, sound insulation and
hearing protection measures must be taken by the
operator.
ASSEMBLY INSTRUCTIONS
BE SURE TO DISCONNECT THE TOOL FROM
THE POWER SUPPLY BEFORE ATTACHING
OR REMOVING THE SAW BLADE. BE SURE THAT
THE TEETH OF THE SAW BLADE ARE POINTING
UPWARD AT THE FRONT OF THE TOOL.
ATTACHING AND REMOVING
THE BLADE (FIGURES 2, 3, 4, AND 5)
ATTACHING THE BLADE
1. Pressing the spindle lock button (1), turn the hex-
190 mm
head bolt (2) with the spanner (3) until the spindle
locks. (Fig.2)
2. Loosen the hex-head bolt by turning the spanner
anticlockwise while pressing the spindle lock button.
(Fig.2)
-1
3. Remove the hex-head bolt and the outer blade
washer (4). (Fig. 2)
4. Retract the lower guard (5) back with the lower guard
lever (6) as far as possible under the upper guard
(7). (Fig. 3)
5. Then, attach the saw blade (8) against the inner blade
washer (9) on the spindle. Then fit the outer blade
washer and the hex-head bolt. (Fig. 3 and 4)
11
H CZ RUS RO PL SLO HR TR