Midland BTX1 Guide D'utilisation page 11

3. Now press long (3 sec) the Middle buttonich button, the Blue and Red light
will flash.
4. Follow the procedure on the other unit's instruction manual (normally you can
use the "Volume +" button on all the previous BT line units).
5. When successfully paired, each unit will have the Blue light on for one second
and than go back to the setup mode (Red light always on).
Exit the setup mode from both units before you can use them: for BTX1 double
click on the Middle button, the Red light will turn off and the Blue light will start
flashing. For the other devices of BT line, please refer to their own user manual.
Talk 2 All - Pairing to a different brand intercom
Thanks to the "Talk2 All - Universal Intercom" feature it is now possible to pair your
BTX1 to a different brand intercom available on the market.
1. On the BTX1 enter the setup mode: (With the unit OFF press and hold down
the Middle button about 7 sec., until the Red light is on permanently.
2. Press the "Forward" button for 3 seconds, the Red and Blu LED light will flash.
3. On the other intercom (not Midland brand) follow the procedure to pair to
a phone.
When successfully paired (no red/blue flashing light), to open the intercom com-
munication on the BTX1 follow the instruction "Manual activation"; on the other
intercom just press the phone redial button.
Attention: when using this configuration, the other intercom (not Midland brand)
will not be able to be paired to a phone.
Pairing the BTX1 to Bluetooth devices
The BTX1 unit can be paired to other Bluetooth devices, like Phone, GPS Navigator
or PMR446 Radio with built-in or external Bluetooth.
The pairing procedure must be done using the "Volume +" buttons.
› Pairing to the "Volume +" button: for Phone or GPS. All devices paired to
this button have higher priority and will interrupt all the other communica-
tion .
› Phone › Background
› GPS feature ON/
› GPS + Phone OFF
› PMR446 Radio
18 - Midland BTX1
Pairing to a phone
The cellular phone can be paired only to the "Volume +", when paired the
"phone mode " is active. In this way it is possible to manage all the phone functio-
nalities and listen to the stereo music. An incoming call the higher priority, that
means all other communications will be closed (Intercom, Music).
Pairing to a GPS navigator
The GPS can be paired on the "Volume +" button, when paired the
"phone mode " is active.
Attention: If you need to connect both Phone and GPS, you must pair the Phone
to the GPS itself.
Pairing to a PMR446 radio with integrated or external Bluetooth
The PMR446 Radio must be paired to the "Volume +" button.
Attention: if you pair a PMR446 with Bluetooth, it will not be possible to pair the
Phone or the GPS.
Bluetooth connection always in Background
This feature let you keep the Bluetooth connection on the "Volume+" button
always in background also if the Intercom is open (very useful to keep the GPS
navigator announcement in background while the intercom is open).
Enabling/Disabling the Background feature:
Keep pressed for three second the "Volume -" button, a voice announcement will
tell you the status. The background feature is active by default.
How to pair the BTX1 to a Phone
To pair the BTX1 to a Phone, you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on
permanently.
3. Now press for 3 seconds the "Volume +" button, the Blue and Red light will flash.
4. Enable the Bluetooth device search feature on your mobile phone
5. After some seconds, "Midland BTX1" will be displayed on your mobile phone.
Follow the pairing procedure of your Phone. If a pin code is requested you
must enter "0000" (four time zero).
When successfully paired, the Blue light of the unit will be on for one second and
than the unit will exit the setup mode and switch to the working mode (the Blue
light will start flashing).
You can use now your BTX1 together with the Phone.
How to use a Phone
in order to use all the phone/MP3 music player feature. If you are in "Intercom"
mode you can only manage the incoming phone call. To activate the "phone"
mode, press the middle button until you hear "Phone" from the voice announce-
ment. Now all the three main button are dedicated to the phone (see Table B)
Answering a call in both Phone/Intercom mode
When you hear the phone ring, you can answer in two different ways:
Vocally:
Simply say one word to answer the call and start talking.
Remembering that you can only do this if you answer the call after the third Ring.
Attention: be aware that some phones may not support voice answering
Manually:
Tap the "Forward" button and start speaking.
Rejecting a call in both Phone/Intercom mode
If you don't wish to answer, you can let the mobile phone ring or press the "For-
ward" button for a few seconds (you will hear one audio confirmation tone).
Making a call only in Phone mode
There are several ways to make a call.
From the mobile keypad:
Dial the number on the mobile keypad:
Press "Send" on the mobile phone.
To redial the last number:
Press "Forward" button for 3 seconds in order to redial the last number (you will
hear one audio confirmation tone).
To make a voice call:
Briefly press "Forward" button. If your mobile phone supports voice calls, you will
be asked to speak the name of the contact you wish to call.
Priority: Calls have a high priority, which means that all other communications are
temporarily disabled when a call arrives and automatically re-enabled once the call
ends.
Ending a callin both Phone/Intercom mode
There are several ways to end a call:
› Wait for the called person to end the call.
› Press the "Forward" button (you will hear an audio confirmation tone).
B-Phone mode
Mode Forward button
Phone Short press: Voice dial /accept or close if it is
in progress
Long press: redial last number/ or reject
incoming call
Phone (when music play) Short press: Forward the song
› Press "End" button on the mobile phone.
Using the MP3 player feature of the mobile phone only in Phone mode
Many mobile phones are now designed to be used as stereo MP3 players. The
BTX1 device fully supports the A2DP and AVRCP protocols that enable you to listen
to stereo music and remotely control your mobile phone's MP3 player. You can
even use the buttons on the BTX1 unit to control the following play options: Play,
Pause, Forward and Backward.
Forward Play/Pausa Backward
Available controls:
› To play/pause music: click on the "Middle" button.
› To skip forward to the next song: press the "Forward" button.
› To skip backwards to the previous song: press the "Rear" button..
Priority: the music listening mode has the lowest priority. Therefore, it will always
be disabled when another type of communication is enabled.
How to pair the BTX1 to a GPS
In general is possible to pair the BTX1 to all the GPS for motorbike that support
Bluetooth headset connection.
To pair the BTX1 to a GPS, you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the "Middle" button about 7 sec., until the Red light is
on permanently.
3. Now press firmly (3 sec) the "Volume +" button, the Blue and Red light will
flash.
4. Enable the Bluetooth device search feature on your GPS
5. After some seconds, "Midland BTX1" will be displayed on your GPS.
Middle button Rear button
Long press: Change mode Long press: toggle on/off wired
Short press: Play/pause Short press: Backward the song
Midland BTX1 - 19
Long press: Change mode