Midland BTX1 Guide D'utilisation page 10

Description of the installation brackets
The Midland BTX1 can be fixed onto the helmet in two different ways: By either
using the plate with bi-adhesive strip, or the clamp. These methods allow you to
safely "fix" the BTX1 unit onto your helmet and to remove it at any time in order
to recharge or store it.
Plate with bi-adhesive strip
The fixing plate has a bi-adhesive strip on one of
its sides. To fix the plate in place, clean the appli-
cation area on the helmet surface, remove the bi-
adhesive film and
place the fixing plate on the helmet by keeping it
contact with the surface for a few seconds.
Screw Clamp
Using the Allen Key, loosen the two screws on the clamp and place the rear plate
between the helmet padding and the external rigid protection. Then, tighten the
two screws in order to firmly fix the clamp in place. Inside the clamp is included a
small plastic spacer that can be removed to give a tighter fit if required.
Fitting and removing your Midland BTX1
The BTX1 can be easily fitted onto the helmet by sliding it downwards so that
it fits into the slot of the selected fixing device (plate with bi-adhesive strip or
clamp). BTX1 is maintained in position thanks to the fixing clip located on the
upper section (A).
To detach the BTX1, simply press the fixing clip and push the unit upwards.
16 - Midland BTX1
Switching your Midland BTX1 on and off
Switching the unit on:
Press and hold "Middle" button down for approximately 3 seconds until the BLUE
indicator lights.
Switching the unit off:
Press and hold both "Middle" and "Rear" buttons together for approximately 3 se-
conds until the RED indicator flashes 3 times, thus lessening the chances that you
might turn off the unit accidentally (especially whilst wearing gloves).
Operative "mode"
The BTX1 can operate in two main "mode": Intercom and Phone.
The 3 multi function buttons can have different functionality depending on which
mode the unit is at that moment.
› In "Intercom mode" the middle buttons let you manage the communications
between driver and passanger
› In "Phone mode" you can manage your Bluetooth cellular phone to place/
answer a phone call or to listen to the music (in stereo mode). Please use your
phone responsibly and safely.
You can switch (toggle) from one mode to the other simply pressing the Middle
button for 3 seconds. A voice announcement will tell in which mode you are on.
The toggle sequence is the following:
› Intercom mode (if another unit has been paired)
› Phone mode (if a phone has been paired)
Every time you turn on the unit, the default mode is Intercom (if it was previously
paired to another unit), otherwise it will be Phone (If was paired to a phone).
If you need to know in which mode the unit currently is, just press the "Volume +
" and "Volume –" button together. A voice announcement will tell you the current
mode.
How to pair two BTX1 unit
The two units supplied in the same BTX1 box, are already paired and ready to use,
which mean you don't need to perform this procedure. The unit are already paired
using the Middle button.
If the devices are not part of the same kit, or the units has been purchased sepa-
rately, you need to first pair it in order to use it.
To pair the BTX1 to another BTX1 unit
To pair the BTX1 to another BTX1 unit, you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on
permanently.
3. Now press the Middle button for 3 seconds. The Blue and Red light will flash.
4. Do the same procedure on the other unit, When successfully paired, each unit
will have the Blue light on for one second and than go back to the setup mode
(Red light always on).
5. Now the pairing procedure is complete, you just need to exit the setup mode
before you can use the units:
6. Double click on the Middle button, the Red light will turn off and the Blue
light will start flashing.
You can use now your BTX1.
How to use the Intercom
To use the intercom feature, be sure the both units are turned on and correctly
paired together.
Manual activation
Press the Middle button on one of the two units. Communication is enabled and
remains active until you press again the middle button. The intercom need some
A- Manual activation
Mode Forward button Middle button
Short press: Open/Close intercom to paired
Intercom
raider
Long press: Change mode
second to activate, you will hear a beep tone when the intercom is open.
Voice activation (VOX)
Simply start talking, after some seconds the communication will be opened and
will remain active for the time you are talking. If there is no conversation the
intercom will be closed after 40 seconds. If needed you can close the intercom
manually without waiting 40 seconds (just press the middle button).
If needed, you can temporarily disable the VOX feature simply by pressing the
Backward button for 7 sec. Two sound beep will advise you when the VOX is di-
sabled. To turn the VOX on again, just press the same button, one beep sound
will advise you that the VOX is now active (or just turn the unit off and on again).
Adjusting the volume
Your Midland BTX1 uses AGC technology, which automatically adjusts the liste-
ning volume in relation to background noises.
However, it is also possible to manually adjust the volume by means of the "Volu-
me +" and "Volume -"buttons.
Attention: volume can be adjust only when an audio connection is active.
Attention: the volume buttons (Vol + and Vol -) cannot be used to adjust the vo-
lume of the wired audio source. The AGC system with automatically increase the
volume on higher speed.
How to pair the BTX1 to previous Midland BT line unit
The BTX1 is compatible with all the BT line unit from Midland. You can pair the
BTX1 to a BT2, BT1 or BTX1 unit and the max distance of the intercom is defined
from the lower possible.
To pair the BTX1 to another BT line unit, you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the Middle button about 7 sec., until the Red light is on
permanently.
Rear button
Long press: Toggle on/off wired
Midland BTX1 - 17