Operating Elements And Connections; Safety Notes; Applications; Setting Into Operation - IMG STAGELINE PARL-10DMX Mode D'emploi

All operating elements and connections described
GB
can be found on the fold-out page 3.

1 Operating Elements and Connections

1 Mounting bracket
2 Control SENSITIVITY for the sensitivity of re-
sponse in case of music control via the microphone
(3)
3 Microphone for music control
4 Mains jack for connection to a socket (230 V~ /
50 Hz) via the supplied mains cable or for connec-
tion to the jack POWER LINK OUTPUT (11) of
another PARL-10DMX
5 Display
6 Power indication
7 Operational buttons
Buttons UP and DOWN for selection of a control
programme and for adjusting the DMX start ad-
dress
Button ENT (= Enter) to memorize an adjustment
Button FUNC to activate the DMX address adjust-
ment
8 Locking screws for the mounting bracket (1)
9 Support for the mains fuse
Only replace a blown fuse by one of the same type
10 Lug for fixing a safety rope
11 Connection POWER LINK OUTPUT for power sup-
ply of another unit
12 DMX signal input (3-pole XLR) for connection of a
light controller;
pin 1 = ground, 2 = DMX-, 3 = DMX+
13 DMX signal output (3-pole XLR) for connection to
the DMX input of another DMX light effect unit;
pin 1 = ground, 2 = DMX-, 3 = DMX+

2 Safety Notes

The unit corresponds to all required directives of the
EU and is therefore marked with
WARNING The unit uses hazardous mains voltage
(230 V~). Leave servicing to skilled per-
sonnel only and do not insert anything
into the air vents; inexpert handling may
result in electric shock.
Please observe the following items in any case:
G
The unit is suitable for indoor use only. Protect it
against dripping water and splash water, high air
8
G
G
G
G
G

3 Applications

This flat LED spotlight serves for illumination e. g. on
stage, in discotheques, and festival rooms. As a light
source, 168 extra bright LEDs with a diameter of 10 mm
are used which have a low power consumption, a low
heat development and a long life. The LEDs allow to
radiate coloured light in the three primary colours (red,
green and blue) and light which can be mixed from the
primary colours by addition. Besides, colour crossfad-
ings and stroboscopic effects are possible.
light controller (4 DMX control channels). However, it
can also be operated on its own, in this case the con-
.
trol is made via programmes to be selected.

4 Setting into Operation

4.1 Mounting
G
humidity, and heat (admissible ambient temperature
range 0 – 40 °C).
Do not place any vessels filled with liquid, e.g. drink-
ing glasses, on the unit.
Do not operate the unit or immediately disconnect
the mains plug from the mains socket
1. if the unit or the mains cable is visibly damaged,
2. if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the unit must be repaired by skilled per-
sonnel.
Never pull the mains cable for disconnecting the
mains plug from the mains socket, always seize the
plug.
For cleaning only use a dry, soft cloth, never use
chemicals or water.
No guarantee claims for the unit and no liability for
any resulting personal damage or material damage
will be accepted if the unit is used for other purposes
than originally intended, if it is not safely mounted or
not correctly operated, or if it is not repaired in an
expert way.
If the unit is to be put out of operation defini-
tively, take it to a local recycling plant for a
disposal which is not harmful to the environ-
ment.
The spotlight is designed for the control via a DMX
Always place the unit so that a sufficient air circula-
tion is ensured during operation. The air vents at the
housing must not be covered in any case.