Black & Decker ASI500 Mode D'emploi page 8

ENGLISH
Switch the main power switch (1) to the inflate position

(c) to power up the LCD.
Warning! Do not leave the inflator running unattended.
It could burst tyres or other items.
Quick start
Warning! Never leave the inflator running unattended in this
mode. It can burst car tyres and other items.
To use your inflator immediately, you can do so without
setting the automatic shut-off feature:
Switch the main power switch (1) to the inflate position

(c, fig E).
To switch between the different units (PSI, BAR or KPA)

press the - & + buttons (21 and 23) together until the
required units are displayed.
Connect the universal valve adaptor (6) and an

accessory, if required, to the item to be inflated, making
sure that the lever (19) of the valve adaptor is in the
down position to lock it in place.
Note: Make sure that the universal valve adaptor is correctly
fitted to the item to be inflated.
To start the inflator press the power button (22) on the

LCD.
When the item is inflated as required or to stop the

inflator at any time press the power button (22) on the
LCD.
Remove the hose from the item and store it on the unit.

Turn the main power switch (1) to the off position (b,

fig. E).
Setting the automatic shut-off pressure (fig. E)
Note: The LCD will only display inflation pressures when the
inflator is being used. Battery status will always be shown.
8
Needs charging.
Charging.
Fully charged.
To switch between the different units (PSI, BAR or

KPA), press - & + buttons (21, 23) together until the
required units are displayed.
Press and hold either of the - & + buttons (21, 23)

for 3 seconds until the display flashes.
While the display is flashing press the - or + buttons

(21, 23) until the required pressure is displayed.
After 3 seconds the display will flash and return to a

reading of "0.0 PSI / 0.00 BAR / 0 KPA". This is normal.
Connect the universal valve adaptor (6) and an

accessory, if required, to the item to be inflated, making
sure that the lever (19) of the valve adaptor is in the
down position to lock it in place.
Note: Make sure that the universal valve adaptor is correctly
fitted to the item to be inflated.
To start the inflator press the power button (22) on the

LCD.
When the item to be inflated has reached the preset

value the unit will automatically stop.
Note: You may notice the actual pressure reading may drop
after a couple of seconds, this is normal.
To stop the inflator at any time press the power button

on (22) the LCD.
Remove the valve adaptor or accessory from the

inflated item and the 12 Vdc adapter (6) from your
vehicle's 12 Vdc accessory socket.
Turn the main power switch (1) to the off position (b).

Note: If the main power switch is turned off, all settings will
be lost and will need to be re-entered following the
instructions under the heading 'Setting the automatic shut-
off pressure (fig. E)'. This is a safety feature to prevent the
risk of items OVER INFLATING.
Using the inflator as a pressure gauge
Switch the main power switch (1) to the inflate

position (c fig. E).
Connect the universal valve adaptor (6) to the item to be

checked.
The LCD will display the items pressure.

After checking, turn the main power switch (1) off and

return the air hose to the storage location.
Operating the high-volume pump
Note: Do not operate the pump when the vehicle's engine
is running.
Note: Make sure that your 12 Vdc accessory socket is live.
On some vehicles the accessory socket may only become
live when the ignition key is in the accessory position.
To inflate using the high-volume pump (i.e air mattresses,
rafts, swimming pool floats):
Note: The pump mode DOES NOT have an auto shut-off
feature.