Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed:
8" or 10" adjustable
wrench (for gas
connections)
Flat-blade screwdriver
Adjustable wrench that
opens to 1" (2.5 cm) or
⁹⁄₁₆" (14 mm) open-end
wrench (for adjusting
washer/dryer feet)
Level
¼" nut driver or socket
wrench (recommended)
Wood block (for leveling)
Ruler or measuring tape
Parts supplied:
Remove parts package from the washer basket. Check that all
parts are included.
A
D
A. Water inlet hoses (2)
B. Inlet hose flat washers (4)
C. Front leveling feet with nuts (2)
D. Shipping strap (not in parts bag,
see "Remove Shipping Strap")
E. Drain hose
F. Silver, double-wire hose clamp
Parts needed:
Check local codes and with gas supplier, check existing gas
supply, electrical supply and venting, and read "Electrical
Requirements," "Gas Supply Requirements" and "Venting
Requirements" before purchasing parts.
Mobile home installations require special parts (listed following)
available for purchase from the dealer from whom you purchased
your dryer. For further information, please reference the
"Assistance or Service" section of the Washer/Dryer User
Instructions.
Mobile Home Installation Kit. Ask for Part Number 346764.
Metal exhaust system hardware.
INSTALLATION INSTRUCTIONS
Knife
Vent clamps
Pipe-joint compound
resistant to LP gas
Caulking gun and
compound (for installing
new exhaust vent)
Pliers that open to
1⁹⁄₁₆" (3.95 cm)
Scissors
Tin snips (new vent
installation)
C
B
F
E
Alternate Parts
Your installation may require additional parts. For information on
ordering, please refer to the toll free phone numbers on the front
page of the Washer/Dryer User Instructions.
If You Have
You Will Need to Buy
Laundry tub or
Sump pump system (if not already
standpipe taller than
available)
96" (2.4 m)
1" (2.5 cm) diameter
2" (5 cm) diameter to 1" (2.5 cm)
standpipe
diameter standpipe adapter, Part
Number 3363920
Overhead sewer
Standard 20 gal. (76 L) 34" (86.4 cm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
Floor drain
Siphon break, Part Number 285320,
additional drain hose, Part Number
285702 and connector kit,
Part Number 285442
Drain hose too short
Drain hose, Part Number 285664 and
connector kit, Part Number 285442
Lint clogged drain
Drain protector, Part Number 367031
Water faucets
2 longer water fill hoses:
beyond reach of fill
6 ft (1.8 m) Part Number 76314,
hoses
10 ft (3.0 m) Part Number 350008
Location Requirements
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Failure to do so can result in death, explosion, or fire.
You will need
A location that allows for proper exhaust installation. A gas
washer/dryer must be exhausted to the outdoors. See
"Venting Requirements."
A grounded electrical outlet located within 2 ft (61 cm) of
either side of the washer/dryer. See "Electrical Requirements."
A sturdy floor to support the washer/dryer weight (washer/
dryer, water and load) of 500 lbs (226.8 kg).
A level floor with a maximum slope of 1" (2.5 cm) under entire
washer/dryer. Clothes may not tumble properly and automatic
sensor cycles may not operate correctly if washer/dryer is not
level. Installing on carpet is not recommended.
3
Publicité
Table des Matières
