Technical Data - Bosch GDB 2500 WE PROFESSIONAL Instructions D'emploi

OBJ_BUCH-114-001.book Page 12 Thursday, September 28, 2006 12:42 PM
Product Features
The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 S 500 A diamond-drill stand*
2 Water outlet connector
3 Residual current device (RCD)
4 Gear selector
5 Feed handle (S 500 A)
6 Water collection ring*
7 Core bit*
8 Sliding ring*
9 Drill spindle
10 Water-flow indicator
11 Water cock
12 Control indicator
13 On/Off switch
*The accessories illustrated or described are not
included as standard delivery.

Technical Data

Diamond Drill
Article number
Rated power input
Output power
Rated speed n
0
– 1. Gear
– 2. Gear
Drilling diameter
– optimum range
– possible range
Tool holder
Water supply pressure
(max.)
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for nominal voltages [U] of
230/240 V. For lower voltage and models for specific coun-
tries, these values can vary.
Please observe the article number on the type plate of your ma-
chine. The trade names of the individual machines may vary.
Noise/Vibration Information
Measured values determined according to EN 61029.
Typically the A-weighted noise level of the machine is:
sound pressure level 89 dB(A); sound power level
102 dB(A). Uncertainty K=3 dB.
Wear hearing protection!
Overall vibrational value (vector sum of three direc-
tions) determined according to EN 60745:
Vibrational emission value a
2
K = 1 m/s .
12 | English
ured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another.
The vibration emission level will vary because of the
ways in which a power tool can be used and may
increase above the level given in this information sheet.
This could lead to a significant underestimate of expo-
sure when the tool is used regularly in such a way.
Note: To be accurate, an estimation of the level of
exposure to vibration experienced during a given period
of work should also take into account the times when
the tool is switched off and when it is running but not
actually doing the job. This may significantly reduce the
exposure level over the total working period.
Declaration of Conformity
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or stand-
ardization documents: EN 61029 according to the
provisions of the directives 89/336/EEC, 98/37/EC.
Dr. Egbert Schneider
Senior Vice President
GDB 2500 WE
Engineering
PROFESSIONAL
0 601 18P 7..
W 2500
W 1450
23.08.2006, Robert Bosch GmbH, Power Tools Division
rpm 440
D-70745 Leinfelden-Echterdingen
rpm 960
mm 82–132
mm 32–212 Assembly
1 1/4" UNC, R 1/2"
Clamping the Machine in the S 500 A
bar 23
Diamond-drill Stand
kg 11.8
/I
To insert the machine into the drill stand, read and
observe the respective operating instructions.
Inserting/Replacing the Core Bit
2
= 2.5 m/s , uncertainty
h
The vibration emission level given in
WARNING
this information sheet has been meas-
Dr. Eckerhard Strötgen
Head of Product
Certification
The safety and operating instructions for the
drill stand being used are to be strictly
observed!
Before any work on the machine itself, during
breaks as well as when not using, secure the
machine against accidental movement by
engaging the feed lock. For this, read and
observe the operating instructions of the drill stand.
3 609 929 A54 • 28.9.06