Bosch KTS 250 Manuel D'utilisation D'origine page 11

For further information, see the KTS 250 Help
Center: " KTS 250 >>
Center".
1. Use the power supply unit provided to supply the
KTS 250 with power.
2. Switch on the KTS 250 by pressing the power key.
3. Select a language.
4. Read and follow the instructions on screen.
After the initial commissioning, an initial update
must be performed. An internet connection is re-
quired for the update.
---Separator---
4.2 Setting up a printer
To use the KTS 250 to print, the KTS 250 must be
in the same computer network as the printer.
 Set up the printer according to the instructions of the
KTS 250 Help Center.
For further information, see the KTS 250 Help
Center: " KTS 250 >>
Center".
---Separator---
4.3 Licensing the software
An internet connection is required for the licens-
ing process.
1. You can find the customer number and password in
the welcoming e-mail that follows conclusion of the
agreement.
2. Enter customer number and password.
3. Use <Continue> to confirm your input.
 The licensing process is now complete.
Should the customer number and/or password
(main menu) >> Settings >> Licens-
be lost, "
ing >> Forgot login information?" can be used to
have the login information sent to the email ad-
dress specified during the ordering process of
the KTS 250.
---Separator---
5. Operation
5.1 Switching on the KTS 250
To prevent the formation of condensation, do not
switch on the KTS 250 until the KTS 250 has ad-
justed to the ambient temperature.
 Switch on the KTS 250 by pressing the power key.
---Separator---
Robert Bosch GmbH
(main menu) >> Help
(main menu) >> Help
Operation | KTS 250 | 11 | en
5.2 Activating power-saving mode
 Press power key briefly.
 The KTS 250 will enter standby mode (power-saving
mode). If power-saving mode is already active, it
will be deactivated.
For further information, see the KTS 250 Help
Center: " KTS 250 >>
Center".
---Separator---
5.3 Switching off the KTS 250
1. Press the power key for approx. 2 seconds, and re-
lease it when the selection menu is opened.
2. Select <Switch off>.
 The KTS 250 will be switched off.
---Separator---
5.4 Forced shutdown
 Hold the power key pressed for at least 10 seconds.
 The KTS 250 will be switched off.
A forced shutdown may result in the loss of input
data.
Use this mode only if a shutdown of the operat-
ing system is not possible, e.g. if the touchscreen
is not responsive (frozen touchscreen) or the
screen remains black.
---Separator---
5.5 Preparing for control unit diagnosis
 Use the KTS 250 with the OBD connection cable inclu-
ded in the scope of delivery only.
If an incorrect OBD connection cable is used, it
may result in malfunctions during control unit di-
agnosis or even damage or destroy vehicle com-
ponents.
The diagnostic connector of the vehicle must be
protected by a fuse with a max. rating of 6 A /
32 V.
 Connect KTS 250 to vehicle via OBD connection cable
1 684 465 756.
For further information on connection options
and pin assignments, see " KTS 250 >> Diagnos-
tic connector".
---Separator---
5.5.1 Searching for vehicle systems
1. Secure the vehicle from rolling off during testing.
— Automatic transmission in park position.
— Manual transmission in neutral position and park-
ing brake engaged or wheels blocked using wheel
chocks.
2. Use the KTS 250 to start the vehicle system search.
For further information, see the KTS 250 Help
Center: " KTS 250 >>
Center".
---Separator---
(main menu) >> Help
(main menu) >> Help
1 689 989 370 | 2018-08-01