Standard Accessories; Applications; Battery Removal/Installation - HIKOKI CJ 14DSL Mode D'emploi

Masquer les pouces Voir aussi pour CJ 14DSL:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 26
CAUTION
1.
If liquid leaking from the battery gets into your eyes,
do not rub your eyes and wash them well with fresh
clean water such as tap water and contact a doctor
immediately.
If left untreated, the liquid may cause eye-problems.
2.
If liquid leaks onto your skin or clothes, wash well
with clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3.
If you find rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using
the battery for the first time, do not use and return it
to your supplier or vendor.
SPECIFICATIONS
Cordless Jig Saw
Model
Voltage
Max. Cutting Depth
No-Load Speed
Stroke
Min. Cutting Radius
Rechargeable battery
Weight
Charger
Model
Charging voltage
Weight

STANDARD ACCESSORIES

1 Blades (No. 41) ....................... 1
Refer to Table 5 for use of the blades.
2 Hexagon bar wrench ............. 1
CJ14DSL
3 Splinter guard ......................... 1
(2LSCK)
4 Chip cover ............................... 1
CJ18DSL
5 Charger ..................................... 1
(2LSCK)
6 Battery ...................................... 2
7 Plastic case .............................. 1
8 Battery cover ........................... 1
CJ14DSL (NN)
Without charger, battery,
CJ18DSL (NN)
plastic case and battery cover
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES ... Sold separately
(1) Various types of blades
Refer to Table 5 for use of the blades.
(2) Guide
(3) Sub base
(4) Dust collector
Optional accessories are subject to change without notice.
CJ14DSL
14.4 V
BSL1430: Li-ion 14.4 V
(3.0 Ah, 8 cells)
2.3 kg
UC18YRSL
14.4 V 18 V
0.6 kg
WARNING
If an electrically conductive foreign object enters the
terminals of the lithium ion battery, a short-circuit may
occur resulting in the risk of fire. Please observe the
following matters when storing the battery.
Do not place electrically conductive cuttings, nails,
steel wire, copper wire or other wire in the storage
case.
Either install the battery in the power tool or store
by securely pressing into the battery cover until the
ventilation holes are concealed to prevent short-
circuits (See Fig. 1).
Wood 135 mm
Mild Steel 10 mm
–1
0 – 2400min
26 mm
25 mm

APPLICATIONS

Cutting various lumber and pocket cutting
Cutting mild steel plate, aluminum plate, and copper
plate
Cutting synthetic resins, such as phenol resin and vinyl
chloride
Cutting thin and soft construction materials
Cutting stainless steel plate (with No. 97 blade)

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch to
remove the battery (See Fig. 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (See
Fig. 2).
CHARGING
Before using the cordless jig saw, charge the battery as
follows.
1. Connect the charger's power cord to a receptacle.
When the power cord is connected, the charger's pilot
lamp will blink in red. (At 1-second intervals)
English
CJ18DSL
18 V
BSL1830: Li-ion 18 V
(3.0 Ah, 10 cells)
2.4 kg
10

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Cj 18dsl

Table des Matières