Manual On Assembly Of The Wall Bracket - ThermoTec AeroFlow MINI 650 Instructions De Montage

Fixing the wall brackets
Only the wall bracket supplied may be used for wall mounting! The latest
regulations according to VDE 0100 part 701 must be complied with for the
installation and operation in damp rooms.
The device may not be mounted directly under a wall socket. In order to avoid
excessive heat radiation upon the wall socket, a certain safety distance must also
be taken into account between the radiator and the wall socket. This distance is
largely determined by the material quality and heat resistance of the locally
installed socket and therefore can not be assessed by us. We assume no liability
for improper handling and possible damages resulting from this. In case of
doubt, consult a specialist before installation. Suitable screws and dowels must
be used depending on the type and condition of the wall material. When
positioning the wall bracket and the heater, please always observe the stipulated
minimum distances (see the following figures).
10 cm
A achment dimensions
Fig. 1
8 cm
All radiators have four temperature-resistant holders, which guarantee optimum
fixing of the heater. Please note the correct hanging position of the upper
(marking 1) and lower (marking 2) holders on the heater (see following figures).
Above
1
Below
2
With the type-specific dimension table, you can obtain the correct positioning
for the U-rails and the holders for the correct mounting and fixing of the radiator.
Radiator type Dim X Dim Y
in mm in mm
MINI 650 232 405
COMPACT 1300 466 405
MIDI 1950 766 405
For the assembly please perform the following steps:
1. The two U-rails must be fixed to the wall whilst observing the minimum
distances and depending on the type-specific X / Y-dimension.
2. The two holders marked with the number 2 are to be inserted into the U-rails
at the bottom.
3. Following this the radiator is hooked into the lower holders and tilted forward
at an angle. Hold the radiator while doing so!
4. The two holders marked with the number 1 are to be inserted into the U-rails
at the top and temporarily pulled up.
5. Finally, place the radiator in a vertical position and press the upper holders
down until the heater is completely fixed in place.
2
1
1
2 2
2
Fig. 2
Dim X
190 mm
Slat Slat
X
holder holder
Radiator type Dim X
in mm
MAXI 2450 1066
SLIM 1200 766
SLIM 1600 1066
SLIM TALL 1600 232
1
1
2
2
Note - alignment of the temperature sensor
The temperature sensor is attached to the bottom of the radiator in a clip. If, due
to the placement of the device in a niche or corner, the room temperature and
the measured temperature is influenced, the sensor can be removed from the
clip. The distance to the radiator can be increased by turning the connection
cable of the sensor. The best way to correct the temperature is in the menu
settings, "temperature correction"
Smart Start (adaptive start control)
With this function, the desired room temperature is met at the start time of the
program. This means that the heater is already heating before the set start time.
This is not a malfunction! Smart Start can only be used in program mode. You can
deactivate Smart Start in the menu item "Programs". When Smart Start is
deactivated, the electric radiator starts heating when the preset start time is
reached.
90 mm
Learning phase: In order to reach the target temperature exactly at the start time
of each programmed time frame, your FlexiSmart performs a learning phase in
Dim Y
the first seven days. During this time, heating is always started 15 minutes before
90 mm
the set start time (in every single time window).
As a result, the FlexiSmart controller learns how fast or slow heating takes place
in the room and adjusts the "smart start time" of heating. After the learning
phase, the FlexiSmart controller decides when to start heating up. Your rooms
will be heated up as effectively as possible.
Switch daylight saving time to standard time
The FlexiSmart controller does not have an automatic changeover between
daylight saving time to standard time. You must change the time manually in the
"Set the time" menu.
Exception: If the FlexiSmart controller is connected to an internet module, an
automatic changeover takes place between daylight saving time to standard
time.
Dim Y
in mm
405
120
120
1040
1
1
2
2
+ -
.
11