Manual For Flexismart Controller; Status-Display - ThermoTec AeroFlow Mode D'emploi

Manual for FlexiSmart controller

The first menu you will see after switching your AeroFlow® heater will show the current time on the top left (for setting see page 11). The large temperature next to the

Status-Display

thermometer icon shows the current room temperature. The small temperature in the lower right corner shows the target temperature.
12:34
21
°C
Depending on the program setting, the following icons are visible:
.7
= Manual mode (program mode Off). The target temperature will be controlled via the arrow buttons.
= The AeroFlow® heater is in program mode (see page 9/10).
15.5°C
= The radiator is about to warm the room. As soon as the set room temperature is reached, this symbol disappears.
! = Open window detected, the AeroFlow® heater is temporarily switched off.
= Holiday Mode: The digit below the icon indicates the number of remaining holidays (see page 10).
= Keylock/Childlock ON (to enable/disable press both arrow buttons simultaneously for min. 5 sec.).
NOTES:
If the clock symbol (program mode) is not displayed, lower or raise the target temperature by using the arrow buttons. The AeroFlow® heater will always hold this temperature.
In case the program mode is enabled (the clock symbol is displayed), the target temperature can also be lowered and raised with the arrow buttons. The manually set target
temperature overrides the program mode until the next preset start or end time of a time frame. The AeroFlow® heater returns to programming mode after then.
To turn the heater off, keep the OK button pressed for at least 5 seconds.
"Standby" will be displayed. Power consumption in standby mode below 0.1 watts.
Temperature-Overview
The display view changes after 5 seconds without pressing a button. The current temperature is displayed on top and the target temperature at bottom.
21.7°C
15
°C
.5
OK
In this menu you can change or view your heating times.
You don't see this menu item?
Enable the programming mode in the configuration menu by switching "Programs" to "ON".
Programs
See
Set heating time
Select this menu if you want to view the heating plan. You can not make changes in this menu item.
Select the day of the week for which you want to see the heating plan.
Thursday
Select day
Start
00:00 08:00
08:00 16:00
16:00 00:00
--:--
--:--
--:--
Set a heating plan according to your preferences.
Choose the day of the week. You can select multiple, non-consecutive days. Navigate with the arrow buttons to the
desired days and select them with OK. Navigate with the arrow buttons to Set frames and press OK.
Monday
Select day
Select Time Frame
00:00 08:00
08:00 16:00
16:00 00:00
--:--
--:--
--:--
Select Time Frame
00:00 08:00
Start time
08:00 16:00
16:00 00:00 00:00
--:--
--:--
--:--
Select Time Frame
00:00 08:00
End time
08:00 16:00
16:00 05:30 00:00
--:--
--:--
--:--
9
See the heating plan on the choosen day. Press OK to exit the menu item display.
End Temp
11,0°C
19,0°C
11,0°C
--:-- -- °C
--:-- -- °C
--:-- -- °C
Use the arrow buttons to select changes to a time frame.
11,0°C
Confirm with OK.
19,0°C
11,0°C
--:-- -- °C
--:-- -- °C
--:-- -- °C
Use the arrow buttons to select the start time for the respective time
11,0°C
frame. Confirm with OK.
19,0°C
11,0°C
--:-- -- °C
--:-- -- °C
--:-- -- °C
Use the arrow buttons to select the end time for the respective time
11,0°C
frame. Confirm with OK.
19,0°C
11,0°C
--:-- -- °C
--:-- -- °C
--:-- -- °C
" "