Manual On Assembly Of Wall Bracket; Manual Wireless Thermostat (Receiver); Manual Wireless Thermostat (Transmitter) - ThermoTec AeroFlow Mode D'emploi

Manual on assembly of wall bracket

Only the wall bracket supplied may be used for wall mounting! The latest
regulations according to VDE 0100 part 701 must be complied with for the
installation and operation in damp rooms.
The device may not be mounted directly under a wall socket. In order to avoid
excessive heat radiation upon the wall socket, a certain safety distance must also
be taken into account between the radiator and the wall socket. This distance is
largely determined by the material quality and heat resistance of the locally
installed socket and therefore can not be assessed by us. We assume no liability
for improper handling and possible damages resulting from this. In case of
doubt, consult a specialist before installation. Suitable screws and dowels must
be used depending on the type and condition of the wall material. When
positioning the wall bracket and the heater, please always observe the stipulated
minimum distances (see the following figures).
10 cm
A achment dimensions
Fig. 1
8 cm
All radiators have four temperature-resistant holders, which guarantee optimum
fixing of the heater. Please note the correct hanging position of the upper
(marking 1) and lower (marking 2) holders on the heater (see following figures).
Above
1
Below
2
With the type-specific dimension table, you always obtain the correct
positioning for the U-rails and the holders for the correct mounting and fixing of
the radiator.
Radiator type Dim X Dim Y
in mm in mm
MINI 650 232
COMPACT 1300 466
MIDI 1950 766
For the assembly please perform the following steps:
1. The two U-rails must be fixed to the wall whilst observing the minimum
distances and depending on the type-specific X / Y-dimension.
2. The two holders marked with the marking 2 are to be inserted into the U-rails
at the bottom.
3. Following this the radiator is hooked into the lower holders and tilted forward
at an angle. Hold the radiator while doing so!
4. The two holders marked with the marking 1 are to be inserted into the U-rails
at the top and temporarily pulled up.
5. Finally, place the radiator in a vertical position and press the upper holders
down until the heater is completely fixed in place.
2
1
1
2 2
2
Fig. 2
Dim X
190 mm
Slat Slat
X
holder holder
Radiator type Dim X
in mm
405 MAXI 2450 1066
405
SLIM 1200 766
405 SLIM 1600 1066
SLIM TALL 1600 232
1
1
2
2

Manual wireless thermostat (receiver)

Operating of a domotics transmitter
Press the button on the receiver for more than 3 seconds until the indicator light
starts to flash.
Two operating modes are possible:
1. Slow flashing: On/off switch
2.Quick flashing: Pulse generator
Switching of the modes
Briefly press the button on the receiver. Set the transmitter
to the configuration mode. Check that the indicator
light on the receiver is not flashing.
Deleting assignment
To delete all assigned products, press the button of the receiver for approx. 30
seconds until the indicator light flashes briefly. All transmitters are now deleted.
90 mm
For detailed information about the wireless transmitter, please refer to the
Dim Y
attached description in the wireless thermostat itself.
90 mm
Manual wireless thermostat
(transmitter)
Operation
Bidirectional wireless protocol on wireless frequency 868 MHz. The range
amounts to 100 to 300 metres (if there are no obstacles). Placement on the wall
or mobile in the room.
Settings
Encoder for on/off and basic settings
Setting buttons + / - with programmable settings for:
- Daily/weekly programming
- Detection of open windows
- Presence detector (with additional motion detector)
- Room temperature control with display screen
- Acoustic signal when switching on / off
- Display of the ambient temperature
- Display of the power consumption (kWh) of the assigned electric heaters
- Holiday program
- Winter time
Dim Y
For detailed information about the wireless transmitter settings, please refer to
in mm
the attached description of the wireless thermostat itself.
405
120
Window open detection
120
Radiators with X3D receivers must be equipped with a temporary radiator
1040
shutdown function to comply with EU Directive 2009/125/EG. To ensure this,
you can purchase wireless opening detectors "DO BL Tyxal+" (Part No. 6412288)
or "MDO BL Tyxal+" (Part No. 6412305) from DELTA DORE . Instructions are
included with the detector. Unfortunately, since we do not have these items in
our program, we are unable to provide assistance for setting them up.
1
1
2
2