Using Your Cleaner; Cleaner Maintenance; Emptying The Dust Container - Hoover MISTRAL TMI 2015 Mode D'emploi

USING yOUR clEANER

1. Extract power cord and plug it into the power supply.
the red marker.
2. Adjust the telescopic tube to the desired height by moving the telescopic tube adjusters
up and raise and lower the handle to the most comfortable cleaning position. [6]
3. carpet & floor Nozzle** - Press the floor type selector pedal on the nozzle
the ideal cleaning mode for the floor type.
hard Floor: brushes are lowered to protect the floor.
Carpet: brushes are raised for the deepest clean.
4. Switch the cleaner on by turning the On - Off / Variable Power control Roller clockwise
on the cleaner main body. [8]
5. Adjust the power level by turning the On-Off / Variable Power control Roller to the
desired level. [8]
6. Switch off at the end of use turning the On-Off / Variable Power control Roller.
Unplug and gently pull the cord, the cord will begin to automatically retract back into
the cleaner. [9]
PARKING AND STORAGE
The flexible hose and tube can be parked for temporary storage while in use [10] or in the
Nanopack storage position when not in use [17]:
1. Retract the telescopic tube to its storage length.
2. Remove the nozzle from the end of the telescopic tube.
3. Remove the hose handle from the telescopic tube.
4. lift the hose latch at the rear of the cleaner [13] and wrap the flexible hose around the
product. [14]
5. Park the hose handle on the product.
6. Assemble the nozzle into the parking slot underneath the product.
7. Assemble the telescopic tube into the remaining parking slot underneath the product.
[17]

clEANER MAINTENANcE

Emptying the dust Container

when the dust reaches the max level indicator on the container, empty the dust
container.
important: To maintain optimum performance do not allow the dust to sit higher than
the max level.
1. Remove the hose from the cleaner.
2. Press the dust container release buttons on the bin cover
out of cleaner. [19]
*Certain models only
** nozzle design may vary according to model
MistralManual__1-4_union.indd 2
[5] Do not pull the cord beyond
[7] to select
[11]
[12]
[15]
[16]
[2]
[18] and lift the dust container
3. Hold the dust container upside down so that the pre-motor filter faces upwards.
Unlatch then unhinge the pre-motor filter frame and remove the pre-motor filter from
the frame. [21] If the filters are dirty refer to section 'cleaning the washable filters.
4. Hold the dust container over a bin, press dust container flap release button to empty
the dust. [23]
5. Use the dusting brush [1S] when necessary to remove excessive dust from the internal
surface of the dust bin.
6. close the dust container flap and relocate the pre-motor filter frame on top of it,
ensuring the latch is well closed. Then refit the dust container into the cleaner.
Cleaning the Washable Filters
The cleaner is fitted with a pre-motor filter. To maintain optimum cleaning performance,
regularly clean the filters. Remove excess dust from the filters by gently tapping them
against the side of a bin. The filters should be washed after every 5 container empties.
[8]
important: all bagless cleaners require regular filter cleaning. Failure to clean your
filters may result in air blockage, overheating and product failure. this may invalidate
your guarantee.
important: regularly check and maintain the filters by following the filter
maintenance instructions , it is also recommended that you purchase new filters after
every 3rd filter wash. this will maintain your cleaners performance.
to access the pre-motor filter:
1. Remove the Dust container from the cleaner mainbody.
2. Hold the Dust container over a bin with one hand, Hold the dust container upside
down so that the pre-motor filter faces upwards. Unlatch then unhinge the pre-motor
filter frame and remove the pre-motor filter from the frame. [21]
3. Gently tap and wash the filter packs using hand warm water.
from the filters with a dry cloth and leave to dry fully before re-using.
4. Reassemble filter packs once fully dry and refit to the cleane.
important: Do not use the product without the pre-motor filter pack fitted.
important: Always ensure the filter packs are fully dry before use.
to access the exhaust filter:
1. Unlock the exhaust filter cover by sliding the button towards the rear of the cleaner.
2. Remove the filter pack from the recess.
3. Gently tap and wash the filter pack using hand warm water.
from the filters with a dry cloth and leave to dry fully before re-using. Reassemble filter
packs once fully dry and refit to the cleaner.
remember: Do not use hot water or detergents. In the unlikely event of the filters
becoming damaged, fit a Genuine Hoover consumable. Do not try and use the product
without a filter fitted.
2
[19]
[22] Remove excess water
[20]
[22] Remove excess water
01/07/2011 17.54.44
gB