Specifications; Legal Notices; Reception Disturbances - Insignia NS-F24TV Guide De L'utilisateur

Insignia NS-F24TV 24" Flat Panel Television
Symptom Possible cause
Poor or no TV station experiencing
sound problems.
MUTE button is
pressed.
Possible local
interference.
Antenna/cable
connector is not
connected.
Volume is set to
minimum.
Television shuts Sleep timer is set
off
Closed TV signal is weak.
Captioning not
working
TV station experiencing
problems or program is
not closed captioned.
Close captioning is not
turned on.
Remote control The remote control is
does not not aimed at the
operate sensor.
Distance is too far or
too much light in the
room.
There is an obstacle in
the path of the beam.
The batteries are weak. Replace the batteries.
The batteries are not
inserted correctly.
Parental control Parental control is set
not working to OFF.
correctly.
News or sports event
being broadcast.
Ratings not set.

Reception disturbances

Most types of television interference can be
remedied by adjusting the height and position of
the VHF/UHF antenna. Outdoor antennas are
recommended for best results if not using cable
or satellite. The most common types of television
interference are shown below. If one of these
symptoms appear when the television is
connected to a Cable TV system, the
disturbance may be caused by the local cable
company broadcast.
IGNITION: Black spots or horizontal
streaks may appear, picture may
flutter or drift. Usually caused by
interference from automobile
ignition systems, neon lamps,
electric drills and other electric
appliances.
GHOSTS: Ghosts are caused by the
television signal following two
paths. One is the direct path and the
other is reflected from tall buildings,
hills, or other objects. Changing the
direction or position of the antenna
may improve the reception.
Possible solution
Try another channel.
Press MUTE button
again.
Check for source of
reception disturbance.
Check cable connection
of VHF/UHF antenna.
Increase the volume.
Set sleep timer to OFF.
Check cable or
VHF/UHF antenna.
Try another channel.

Specifications

Press the CCD button.
Aim the remote control
Power Supply
at the remote sensor.
Power Consumption
Dimensions (W x H x D) 26.9" X 20.3" X 19.4"
Operate the remote
within 15 feet of the
television or reduce the
Weight
light in the room.
CRT
Clear the path of the
Audio Output
beam.
TV System
Channel Coverage
Reinsert the batteries.
Antenna Impedance
Set parental control to
ON.
Accessory
Parental control does

Legal notices

not work with news or
sporting events.
Set ratings. FCC Part 15
FCC warning
www.insignia-products.com
SNOW: If your receiver is located in
the fringe area of a television station
where the signal is weak, your
picture may be marred by the
appearance of small dots. When the
signal is extremely weak, it may be
necessary to install an external
antenna to improve the picture.
RADIO FREQUENCY
INTERFERENCE: This interference
produces moving ripples or
diagonal streaks, and in some
cases, causes loss of contrast in the
picture.
PICTURE SIZE VARIATION: A slight
picture size variation is normal
when you adjust the CONTRAST or
BRIGHTNESS setting.
Design and specifications are subject to change
without notice.
AC 120V, 60Hz
110 W
(682 mm x 515 mm x 493 mm)
64 lbs (29 kg)
24" (609 mm)
4W x 2
NTSC-M, ATSC
VHF 2-13, UHF 14-69, CATV 1-125,
CADTV 1-135, DTV 2-69
75 ohm
Remote control
This device complies with Part 15 of the FCC Rules.
Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply within
the limits for a class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for
help.
Changes or modifications not expressly approved by the
party responsible for compliance with the FCC Rules could
void the user's authority to operate this equipment.
17