Technical Data; Accessories - Gardena EasyCut 450/25 Mode D'emploi

6. TROUBLESHOOTING
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the cutting filament to stop and disconnect the
product from the mains before you troubleshoot the product.
To replace the filament cassette [ Fig. T1 / T2 / T3 ]:
DANGER! Risk of injury!
Risk of injury from metal cutting parts!
v Do not use metal cutting parts or replacement parts and
accessories not approved by GARDENA.
v Only use original GARDENA Filament Cassettes.
If the wear rib (29) is no longer visible, the cassette cover
replaced. Contact the GARDENA Service.
You can order the Replacement Filament Cassettes from your GARDENA
dealer or directly from the GARDENA Customer Service.
• GARDENA Filament Cassette for Trimmers Art. 5307
1. Push in cassette cover (21)
and remove it.
2. Remove the filament cassette
3. Remove all possible dirt of the filament cassette holder
4. Pull approx. 15 cm of the cutting filament
cassette (23) through the hole in the plastic ring
(18)
5. Put the cutting filament
(18)
6. Put the cutting filament
7. Put the filament cassette
8. Attach the cassette cover
both locking clips audibly engage.
Make sure that the cutting filament is not squeezed.
If the cassette cover (21) cannot be attached, turn the filament cassette
back and forth, until the filament cassette
cassette holder (24) .
An additional filament cassette
carrier (28) on the trimmer.
v Push the filament cassette
it engages.
Problem Possible Cause
Trimmer does not cut Cutting filament is worn or too
short.
Filament cassette is empty.
Cutting filament is pulled into
the cassette or welded.
Cutting filament cannot be Cutting filament became too
extended or is used quickly dry and brittle (e. g. during the
winter).
Cutting filament frequently
touched hard objects.
Trimmer does not start Engine is blocked.
Trimmer can no longer be Start lever is stuck.
stopped
NOTE: For any other malfunctions please contact the GARDENA service depart-
ment. Repairs must only be done by GARDENA service departments or specialist
dealers approved by GARDENA.

7. TECHNICAL DATA

Trimmer
Unit
Rated Power W
Mains voltage V (AC)
Mains frequency Hz
Cutting width cm
10
9870-20.960.03.indd 10
(21)
(22)
on the two locking clips at the same time
(23)
.
(24) .
(18)
out of the new filament
(25) .
(26)
through the metal sleeve .
(27)
around the guide pin .
(23) into the filament cassette holder
(21)
on the filament cassette holder
(23)
is completely in the filament
(23)
can be attached to the thread spool
(23)
onto the filament cassette carrier
Remedy
v Extend the cutting filament
(see 3. OPERATION
To extend the cutting filament
(Tip mechanism) ).
v Replace the filament
cassette.
v Pull the cutting filament out of
the filament cassette.
v Put the filament cassette in
water for approx. 10 hours.
v Prevent the cutting filament
from touching hard objects.
v Remove the obstacle.
Start again.
v Disconnect the trimmer
from the mains and loosen
the start lever.
Value Value Value
(Art. 9870) (Art. 9872) (Art. 9874)
450 550 650
230 230 230
50 50 50
25 28 28
Trimmer
Rpm of filament cassette
Cutting filament supply
Cutting filament feed
Weight
Sound pressure level L
pA
Uncertainty k
pA
Sound power level L :
2)
WA
measured/guaranteed
Uncertainty k
WA
Hand/arm vibration a
1)
vhw
Uncertainty k
vhw
Measuring process complying with:
NOTE: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
must be
power tool with another. It can also be used for preliminary evaluation of expo-
sure. The vibration emission value can vary during actual use of the electric power tool.

8. ACCESSORIES

GARDENA Filament Cassette
for trimmers
GARDENA Replacement
Cassette Cover
GARDENA Wheel set
for trimmer (only for
Art. 9872 / 9874)
(24) .
(24)
until
9. SERVICE / WARRANTY
(23)
Service:
Please contact the address on the back page.
Warranty statement:
In the event of a warranty claim, no charge is levied to you for the services
(28)
until
provided.
GARDENA Manufacturing GmbH grants a warranty for all original
GARDENA new products for two years from the date of original pur-
chase from the retailer, provided that the devices have been for private
use only. This manufacturer's warranty does not apply to products
acquired second hand.
This warranty includes all significant defects of the product that can be
proved to be material or manufacturing faults.
This warranty is fulfilled by supplying a fully functional replacement product
or by repairing the faulty product sent to us free of charge; we reserve
the right to choose between these options. This service is subject to the
following provisions:
• The product has been used for its intended purpose as per the recom-
mendations in the operating instructions.
• Neither the purchaser nor a third party has attempted to open or repair
the product.
• Only Original GARDENA replacement parts and wear parts have been
used for operation.
• Presentation of the receipt
Normal wear and tear of parts and components (such as blades, blade
fixing parts, turbines, light bulbs, V-belts / toothed belts, impellers, air
filters, spark plugs), visual changes, wear parts and consumables are
excluded from the warranty.
This manufacturer's warranty is limited to replacement and repair of
products in accordance with the abovementioned conditions. The manu-
facturer's warranty does not constitute an entitlement to lodge other
claims against us as a manufacturer, such as for damages. This manu-
facturer's warranty does not, of course, affect statutory and contractual
warranty claims against the dealer / retailer.
The manufacturer's warranty is governed by the law of the Federal
Republic of Germany.
In case of a warranty claim, please return the faulty product, together with
a copy of the receipt and a description of the fault, with postage paid to
the service address.
Consumables:
The filament cassette and the cassette cover are consumables and are not
included in the warranty.
Unit Value Value
(Art. 9870) (Art. 9872)
R/min. 11800 11500
m 6 6
Tip mechanism Tip mechanism Tip mechanism
kg 2.6 2.8
80 82
1)
dB (A)
2.5 2.5
94 / 95 95 / 96
dB (A)
1 1
< 2.5 3.2
m/s
2
1.5 1.5
EN 50636-2-91 RL 2000/14/EC
1) 2)
As replacement for consumed filament cassettes.
Available via the GARDENA Service.
For easy cutting of lawn edges.
Value
(Art. 9874)
11500
6
3.0
83
2.5
95 / 96
1
2.5
1.5
Art. 5307
Art. 9880
11.10.19 08:53