Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
The product must only be installed by qualified personnel, according to the local safety standards and regulations.
Installation warnings
•
The product must not be exposed to dripping or splashing liquids so must be installed indoors in a dry place.
•
Humidity and condensation could damage the product. In case of condensation, wait until the product is dry before
using it.
•
Don't install the product above or close to heat sources, in dusty places or where it might come into contact with
corrosive substances.
•
Leave enough space around the product housing to ensure sufficient ventilation.
•
An excessive operating temperature and/or excessive heat may affect the performance and the life of the product.
In accordance with the European Directive 2004/108/EC (EMC), the product must be installed using devices, cables and
accessories that comply with this directive requirements for fixed installations.
Earthing of the antenna system
The DIN bar, where the unit will be installed, must be connected to the earth electrode of the antenna system, in accordance
with standard EN 60728-11. It is recommended that the provisions of EN 60728-11 are followed and to not connect the
DIN bar to the protective earth (PE) of the mains supply.
IMPORTANT: Only trained and authorized personnel can open the product.
In case of failure, do not try to repair the product, otherwise the guarantee will no longer be valid.
European directives conformity: It complies with the standard EN 50083-2 (European Directive 2004/108/EC – EMC)
The following is contained in the packaging:
•
1 KDF receiver
•
1 RJ45 connector plug. After programming the module, we recommend that the RJ45 connector plug is replaced to
avoid the build up of dust or other particles.
The unit must be installed by attaching it to the DIN bar by pulling down the clip placed on the back of the receiver as
shown in fig. 1.
The KDF receiver must be powered by connecting the red power cable situated on the upper side of the unit to a power
supply able to deliver a voltage of 12V DC (for example a KP35). When used in cascade, it is possible to get power from
the red socket on the upper side of another KDF receiver using the red power cable.
When the product is correctly powered, the green LED on the front is on.
Fig. 2 shows the 4 connectors:
•
SAT IN: Connect a SAT signal from an LNB with an H/V output or as an alternative, the self-demixed output (SAT OUT)
of another KDF receiver can be connected via a KRF15 jumper.
•
MIX IN: This input can be connected to the output of the converted signal (OUT) coming from another KDF receiver
through a KRF15 jumper or, as an alternative, it can be terminated using a 75 Ohm load.
•
SAT OUT: This output can be connected to the SAT IN input of another KDF receiver or, as an alternative, it can be
terminated using a 75 Ohm load.
•
OUT: Output of the converted signal. This output can be connected to the MIX IN input of another KDF receiver via a
KRF15 jumper. With the trimmer situated on the front of the KDF receiver, the RF output level can be regulated.
When KDF receivers are used in cascade, we recommend programming the KDF receivers closest to the output on the
highest frequencies in order to obtain an equalised signal on the output from the series.
The programming of the KDF receiver should be carried out using a TPE programmer by connecting it to the receiver's
RJ45 outlet.
The menu item can be highlighted by scrolling with the
Press
or
to enter the required menu.
Press the
keys to scroll through the values in the menu item.
Press the
key to save the set value in required menu item.
IMPORTANT: Press the TPE
modifications, the set data will be lost.
2. SAFETY WARNINGS
3. PRODUCT INSTALLATION
4. USER'S INSTRUCTIONS
5. PROGRAMMING INSTRUCTIONS
key to save the settings. If this key is not pressed within 5 minutes from the last
10
keys.
Publicité
Table des Matières
