To Start The Product; To Stop The Product - Husqvarna LC 247 Manuel D'utilisation

Before you operate the product
1. Read the operator's manual carefully and make sure
that you understand the instructions.
2. Examine the cutting equipment to make sure that it
is correctly attached and adjusted. Refer to
examine the cutting equipment on page 13 .
3. Do a check of the oil level and fill with engine oil if it
is necessary. Refer to
on page 14 .
4. Fill the fuel tank. Refer to
To fill fuel
If available, use low-emission/alkylate gasoline. If low-
emission/alkylate gasoline is not available, use good
quality unleaded gasoline or leaded gasoline with octane
number not less than 90.
CAUTION:
octane number less than 90 RON (87 AKI).
This can cause damage to the product.
1. Open the fuel tank cap slowly to release the
pressure.
2. Fill slowly with a fuel can. If you spill fuel, remove it
with a cloth and let remaining fuel dry off.
3. Clean the area around the fuel tank cap.
4. Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
5. Move the product a minimum of 3 m (10 ft) from the
position where you filled the tank before a start.
To set the cutting height
The cutting height can be adjusted in 6 levels.
1. Move the cutting height lever rearward to decrease
the cutting height.
2. Move the cutting height lever forward to increase the
cutting height. (Fig. 27)
CAUTION:
too low. The blades can hit the ground if the
surface of the lawn is not level.

To start the product

• Make sure that the ignition cable is connected to the
spark plug.
Manual start (LC 247, LC 247S, LC 253S,
LC 347V, LC 353V)
1. Stay behind the product.
2. Hold the engine brake handle against the handlebar.
(Fig. 28)
3. Hold the starter rope handle with your right hand.
808 - 006 - 22.10.2021
To
To do a check of the oil level
To fill fuel on page 11 .
Do not use gasoline with an
Do not set the cutting height
4. Slowly pull out the starter rope until you feel some
resistance.
5. Pull with force to start the engine.
WARNING:
rope around your hand.
Electrical start (LC 347VE, LC 353VE)
1. Make sure that the battery is charged. Refer to
use the battery for the first time on page 14 .
2. Attach the battery to the engine. The battery locks
into position when you hear a click. (Fig. 29)
3. Stay behind the product and hold the engine brake
handle (A) against the handlebar. (Fig. 30)
4. Push and hold the electrical start button (B) for 3-5
seconds. The engine starts.
Note:
If the engine does not start, wait 1 minute
and try to start the product again.
To use the drive on the wheels
• For models with drive bail, pull the drive bail in the
direction of the upper handle. (Fig. 31)
• For models with speed control, move the speed
control lever forward to increase the speed and
rearward to decrease the speed. (Fig. 32)
• Before you pull the product rearward, disengage the
drive and push the product forward approximately 10
cm.
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.

To stop the product

• To stop the engine, release the engine brake handle.
To remove the battery (LC 347VE & LC
353VE)
To prevent accidental start of the engine, remove the
battery when the product is not in operation.
• Push the lock button (A) and pull the battery straight
out. (Fig. 33)
To get a good result
• Always use a sharp blade. A blunt blade gives an
irregular result and the cut surface of the grass
becomes yellow. A sharp blade also uses less
energy than a blunt blade.
• Do not cut more than ⅓ of the length of the grass.
Cut first with the cutting height set high. Examine the
result and lower the cutting height to an applicable
level. If the grass is very long, drive slowly and cut 2
times if necessary.
• Cut in different directions each time to prevent
stripes in the lawn.
Do not twist the starter
To
11