Functional Description; Extension Cords - Milwaukee 8975-6 Manuel De L'utilisateur

• Wear a dust respirator mask or a dual filter (dust
and fume) respirator mask which has been approved
by the Occupational Safety and Health Administration
(OSHA), the National Institute of Safety and Health
(NIOSH), or the United States Bureau of Mines. These
masks and replaceable filters are readily available at
major hardware stores. Be sure the mask fits. Beards
and facial hair may keep masks from sealing properly.
Change filters often. DISPOSABLE PAPER MASKS
ARE NOT ADEQUATE.
• Use caution when operating the heat gun. Keep the
heat gun moving to prevent excessive temperatures.
Excessive heat can cause paint and other materials
to burn and cause fumes, which may be inhaled by
the operator.
• Keep work environment clean. Keep food and drink
away from work area. Wash hands, arms and face
and rinse mouth before eating and drinking. Do not
smoke, or chew gum or tobacco in the work area. Paint
scrapings and dust created from removing paint may
contain chemicals that are hazardous.
• Clean up all paint scraping and dust. DO NOT
SWEEP, DRY DUST OR VACUUM. Wet mop floors.
Use a wet cloth to clean all walls, sills and other sur-
faces where paint and dust have accumulated. Use a
high phosphate detergent, trisodium phosphate (TSP),
or a trisodium phosphate substitute to clean and mop
the work area.
• Dispose of paint scrapings properly. Following each
work session, place paint scrapings in a double plastic
bag, close it with tape or twist ties and dispose.
• Remove protective clothing and work shoes in
the work area to avoid transferring dust to other
parts of the building. Wash work clothes separately.
Wipe shoes off with a wet rag that is then washed with
the work clothes. Wash hair and body thoroughly with
soap and water.
SAVE THESE INSTRUCTIONS
SYMBOLOGY
Double Insulated
Volts
Alternating Current
Amps
Watts
UL Listing for Canada and U.S.
C US
SPECIFICATIONS
Volts .............................................................120 AC
Max. Amps ........................................................11.6
Max. Watts .......................................................1400
Cat. No. ....................................................... 8977-6
Temperature .......570° F / 1000° F (300°C / 540°C)
Airflow CFM* ........................................................15
Cat. No. ..................................................... 8977-20
Temperature .........100° F / 1040° F (38°C / 560°C)
Airflow CFM* ........................................................20
*Cubic feet per minute

FUNCTIONAL DESCRIPTION

3
2
1
8
1. Accessory
attachment area
2. Nozzle
3. Front cover
4. Nameplate (on back)
5. Intake vents
6. Handle
7. Support stand
8. High/Low switch (8975-6)
Heat/Cool-down mode switch (8977-20)
9. Variable temperature dial (8977-20 only)

EXTENSION CORDS

Grounded tools require a three wire extension
cord. Double insulated tools can use either a two
or three wire extension cord. As the distance from
the supply outlet increases, you must use a heavier
gauge extension cord. Using extension cords with
inadequately sized wire causes a serious drop in
voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the
required minimum wire size.
The smaller the gauge number of the wire, the greater
the capacity of the cord. For example, a 14 gauge
cord can carry a higher current than a 16 gauge cord.
When using more than one extension cord to make
up the total length, be sure each cord contains at
least the minimum wire size required. If you are using
one extension cord for more than one tool, add the
nameplate amperes and use the sum to determine
the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure
it is marked with the suffix "W-A" ("W" in Canada)
to indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired
and in good electrical condition. Always replace a
damaged extension cord or have it repaired by a
qualified person before using it.
• Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Recommended Minimum Wire Gauge
For Extension Cords*
Nameplate Amps
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
* Based on limiting the line voltage drop to five volts at 150%
of the rated amperes.
READ AND SAVE ALL INSTRUCTIONS
FOR FUTURE USE.
4
4 5
6
7
Extension Cord Length
25' 50' 75' 100'
18 18 18 18
18 18 18 16
18 18 16 14
18 16 14 12
16 14 12 10
14 12 10 --
12 10 -- --
9
150'
16
14
12
12
--
--
--