Kickback And Related Warnings; Safety Warnings Specific For Grinding Operations; Additional Safety Rules - RIDGID R1006 Manuel D'utilisation

SPECIFIC SAFETY RULES
 Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in elec-
trocution or shock.

kICkBACk AND RELATED wARNINGS

Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the accessory's
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on direction
of the wheel's movement at the point of pinching. Abrasive
wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
 Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use side handle, if provided, for maxi-
mum control over kickback or torque reaction during
start-up. The operator can control torque reactions or
kickback forces, if proper precautions are taken.
 Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
 Do not position your body in the area where power
tool will move if kickback occurs. Kickback will propel
the tool in direction opposite to the wheel's movement
at the point of snagging.
 Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
 Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent kick-
back and loss of control.
SAFETY wARNINGS SPECIFIC FOR GRINDING
OPERATIONS
 Use only wheel types that are recommended for your
power tool and the specific guard designed for the
selected wheel. Wheels for which the power tool was not
designed cannot be adequately guarded and are unsafe.
 The guard must be securely attached to the power
tool and positioned for maximum safety, so the least
amount of wheel is exposed towards the operator.
The guard helps to protect operator from broken wheel
fragments and accidental contact with wheel.
 wheels must be used only for recommended appli-
cations. For example: do not grind with the side of
an abrasive cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
 Always use undamaged wheel flanges that are of cor-
rect size and shape for your selected wheel. Proper
wheel flanges support the wheel thus reducing the pos-
sibility of wheel breakage. Flanges for cut-off wheels may
be different from grinding wheel flanges.
 Do not use worn down wheels from larger power tools.
Wheel intended for larger power tool is not suitable for
the higher speed of a smaller tool and may burst.
 Always use proper guard with grinding wheel. A
guard protects operator from broken wheel fragments.
 Accessories must be rated for at least the speed
recommended on the tool warning label. Wheels and
other accessories running over rated speed can fly apart
and cause injury.

ADDITIONAL SAFETY RULES

 know your power tool. Read operator's manual care-
fully. Learn its applications and limitations, as well as
the specific potential hazards related to this power
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
 Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT safety
glasses. Following this rule will reduce the risk of serious
personal injury.
 Protect your lungs. wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
 Protect your hearing. wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
 Inspect power tool cords periodically and, if damaged,
have repaired at your nearest Authorized Service Cen-
ter. Constantly stay aware of cord location. Following
this rule will reduce the risk of electric shock or fire.
 Check damaged parts. Before further use of the power
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
4 - English