Adjusting The Pendulum Stroke; Working With The Machine; Free Hand According To The Scribe Mark; Plunge Cutting Without Pilot Drilling - Festool TRION PS 300 Q Notice D'utilisation D'origine

TRION
GB

push base runner to rear position so that the
centring pin [5-1] fits in the opening [5-3],

tighten locking screw [4-1].
7.7

Adjusting the pendulum stroke

In order to process different materials with an opti-
mum feed movement the pendulum jigsaws have
an adjustable pendulum stroke. Select the desired
setting with the pendulum stroke switch [1-5]:
setting 0 = pendulum stroke off
setting 3 = maximum pendulum stroke
Recommended settings of the pendulum
stroke
Hard and soft wood,chip board, wood
fibre board
Wood core plywood, plywood, plastics
Ceramic
Aluminium, NF metals
Steel
7.8 Adjusting the number of strokes
PSB 300 Q, PSB 300 EQ
You can regulate the number of strokes steplessly
between 1000 and 2900 min
wheel [1-2; 2-3]. This enables you to optimise the
cutting speed to suit the material.
Recommended number of strokes (adjusting
wheel setting)
Hard and soft wood, wood core plywood,
plywood, chip board
Wood fibre boards
Plastics
Ceramic, aluminium, NF metals
Steel
8

Working with the machine

WARNING
Risk of injury

Always secure the workpiece in such a manner
that it cannot move while being machined.
8.1

Free hand according to the scribe mark

The triangular shape of the splinterguard [4-3]
shows the cutting line of the saw blade and thus fa-
cilitates cutting to a scribe mark.
14
1 - 3
1 - 2
0
0 - 2
0 - 1
-1
using the adjusting
6
4 - 6
3 - 6
3 - 5
2 - 4
8.2

Plunge cutting without pilot drilling

The base runner must be in the front position for
plunge cuts in timber materials (basic setting, see
Figure [1]).

Place saw on the front edge of the runner.

Set saw to maximum no. of strokes and pendu-
lum stroke setting 3 and start the plunge cut
into the workpiece (Figure [6]).
9

Service and maintenance

WARNING
Risk of injury, electric shock

Always disconnect the mains plug from the
socket before performing maintenance work on
the machine!

All maintenance and repair work which requires
the motor housing to be opened must only be
carried out by an authorised service workshop.
Damaged safety devices and components must be
repaired or replaced in a recognised specialist
workshop, unless otherwise indicated in the oper-
ating manual.
To ensure constant air circulation, always keep the
cooling air openings in the motor housing clean and
free of blockages.
10

Accessories

The order numbers of the accessories and tools can
be found in the Festool catalogue or on the Internet
under "www.festool.com".
10.1

Festool guide system FS

The use of the Festool guide system FS (Figure
[7])facilitates the production of straight and precise
cuts, particularly with material thicknesses up to
20 mm. The jigsaw is hereby placed in a guide stop
[7-1] order no. 490031) and guided along the guide
rail in this. The guide stop has two adjustable limit
stops [7-2] for a setting free from play. Use only
crossed saw-blades when utilising the guide stop.
We recommend Festool saw blade S 75/4 FSG.
10.2

Parallel guide

Use the parallel guide (order no. 490119) to guide
the jigsaw parallel to the workpiece edge. The par-
allel guide can be fitted on both sides of the base
runner:

Slide clamping clip [8-1] onto the base runner
from the front,

insert parallel guide [8-2] through the clamping
clip from the side to the desired position,

tighten rotary knob [8-3].