Maintenance And Service; Maintenance And Cleaning - Bosch PML LI Notice Originale

OBJ_BUCH-1197-003.book Page 10 Tuesday, May 29, 2012 9:11 AM
10 | English
Battery Adapter (see figure B)
Mount components to the worklight only when the bat-
tery 14 is not inserted.
Note: When inserting a completely mounted cordless work-
light with the battery into the battery charger, the cordless
worklight is automatically deactivated.
Connecting the lamp head with flexible neck to the battery
adapter 12 makes a stand-lamp; connecting the head lamp to
the connection cableon the universal adapter makes a head
lamp, or connecting the lamp head to the pipe clamp makes a
spotlight.
Connect the base of the flexible neck 2 or the base of the con-
nection cable 3 with the battery adapter 12. Do not pull the
cable!
The On/Off switch 11 as well as the operation and charge-
control indicator 10, which lights up green as soon as a bat-
tery is inserted and the cordless worklight is switched on, are
on the battery adapter 12. When the battery capacity is below
25 %, the indicator lights up red.
Storage in the Protective Pouch
(see figures C–D)
The protective pouch 9 is used for storage of the battery 14
together with the battery adapter 12. Position the battery
adapter in such a manner that you can operate the On/Off
switch 11 behind the symbol on the pouch. The connection
cable 3 can be conducted through the slot in the pouch.
The protective pouch 9 can be fastened to your belt by the
loop on its backside or to any object with a Velcro strap.
Mounting to a Stand-lamp (see figures B and E)
With the flexible neck 2, you can convert the cordless work-
light to a stand-lamp.
– Guide the base of the flexible neck alongside the guide
grooves in the seat of the battery adapter 12 until it engages.
– Insert lamp head 1 into the flexible neck 2 until it engages.
– Insert the plug of the cable from the flexible neck 2 into the
socket of the lamp head 1.
– Insert a battery (see "Inserting the Battery", page 9).
Removing the Lamp Head (see figure F)
Firstly, switch off the cordless worklight and remove the bat-
tery. To remove the lamp head 1, pull out the cable, lightly
press release lever 16 upward and pull the lamp head toward
the rear off of the component.
Mounting with Pipe Clamp (see figures B and G)
The pipe clamp 8 is used for fastening the cordless worklight
to pipes, handrails, tent poles, etc.
For optimal alignment of the light beam, the pipe clamp can
be swivelled up to 12.5° to the right or left.
Mounting with Head Strap (see figures B and H)
With the universal adapter 6 and the head strap 5, the cord-
less worklight can be used as a headlamp.
The universal adapter 6 can be tilted for optimal alignment of
the light beam.
1 609 929 W51 | (29.5.12)
Universal Adapter with Velcro Strap
(see figures B and I)
With the universal adapter and a Velcro strap, the cordless
worklight can be used anywhere.
The universal adapter 6 can be tilted for optimal alignment of
the light beam.
Operation
Initial Operation
Switching On and Off
To start the cordless worklight, press the On/Off switch 11.
When not using the cordless worklight, switch it off in order to
extend the battery life.
Working Advice
Lens Plate (see figure J)
The lens plate 13 is used to scatter or diffuse the light when
using the cordless worklight e.g., as a reading lamp.

Maintenance and Service

Maintenance and Cleaning

When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.
The cordless worklight is maintenance-free and and contains
no components that must be replaced or maintained.
To avoid damage, clean the plastic lens of the cordless work-
light only with a dry, soft cloth. Do not use cleaning agents or
solvent.
If the cordless worklight should fail despite the care taken in
manufacturing and testing procedures, repair should be car-
ried out by an authorized after-sales service agent for Bosch
power tools.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the cordless worklight.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can
also be found under:
www.bosch-pt.com
Our customer service representatives can answer your ques-
tions concerning possible applications and adjustment of
products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: boschservicecentre@bosch.com
Bosch Power Tools