Applications; Mounting; Setting Into Operation; Operation - IMG STAGELINE PARL-40DMX Mode D'emploi

connected to the terminal which is marked
with the letter N or coloured black .
3 . The wire which is coloured brown must be
connected to the terminal which is marked
with the letter L or coloured red .
Warning – This appliance must be earthed.
If the unit is to be put out of operation
definitively, take it to a local recycling plant
for a disposal which is not harmful to the
environment .

3 Applications

This LED spotlight serves for illumination e . g . on
stage, in discotheques, and festival rooms . As a light
source, four extra bright LEDs are used . The spotlight
is designed for control via a DMX light controller
(8, 6, 5, 4 or 3 DMX control channels available) .
However, it can also be operated independently .
As a special feature for DMX operation the
PARL-40DMX offers the use of 66 sub-addresses .
Thus, it is possible to control up to 66 spotlights
(spotlight groups) via a single DMX start address
independently of each other and the maximum
number of DMX-controlled units is considerably
increased .

4 Mounting

•
Always place the unit so that a sufficient air
circulation is ensured during operation . The air
vents at the housing must not be covered in
any case .
•
The distance to the illuminated object should be
50 cm as a minimum .
WARNING The spotlight must be mounted in a
safe and expert way . If it is installed
at a place where people may walk
or sit under, it must additionally be
secured (e . g . by a safety rope at the mounting
bracket; fix the safety rope so that the maximum
falling distance of the unit would not exceed 20 cm) .
1 . Fix the spotlight via the mounting brackets (1),
e . g . with a stable mounting screw or a support
for lighting units (C hook) to a cross bar .
To align the spotlight, release the two lock-
ing screws (3) at the mounting bracket . Adjust
the desired inclination of the spotlight and
retighten the screws .
2 . As an alternative the spotlight can also be set up
as desired . Spread the mounting brackets under
the spotlight so that they serve as a support .
Then tighten the locking screws .

5 Setting into Operation

WARNING
Never look directly into the light
source for a longer time, this may
cause eye damage .
Please note that fast changes in lighting may trig-
ger epileptic seizures with photosensitive persons
or persons with epilepsy!
1) Connect the plug of the mains cable (8) to a
socket (230 V~ / 50 Hz) . Then the spotlight is
switched on . The display (2) shows the adjusted
operating mode .
2) The display can be adjusted so that it will be
extinguished after 15 seconds approx . (as soon
as a button is actuated, the display lights up
again for 15 seconds) or so that it is always
illuminated . For this purpose see chapter 6 .4
"Automatic display switch-off" .
Note: The unit is protected against overheating . Thus, it
will be switched off when the temperature is too high and
be switched on again automatically after cooling down .

6 Operation

The operating buttons MENU, ,  und ENTER
(7)serve to select the operating mode and different
functions . The fig . 1 on page 3 shows how the
modes and functions are selected via a menu and
shown by the display (2) .
Note: After an adjustment wait for 20 seconds before you
switch off the spotlight, otherwise the adjustment will not
be memorized . When memorizing, the display will
briefly flicker . If the display switch-off has been
activated ( chapter 6 .4), the display will go blank
☞
after memorizing .

6.1 Operation without DMX controller

For the independent operation 3 modes are available .

6.1.1 Colour spotlight and stroboscope

In this mode the spotlight constantly radiates light
in an adjustable colour . In addition, the stroboscope
function can be activated .
1) Press the button MENU repeatedly until the
indication on the display does not change any
more . The display now shows the operating
mode ( ☞ fig . 1 on the very left) .
2) Press the button  or  repeatedly until the
display shows
3) Press the button ENTER . The display now shows
, , , or and a number .
= brightness of red
= brightness of green (0 – 255)
.
(0 – 255)
11