Vibration Information; English - Milwaukee M18 CH Notice Originale

TECHNICAL DATA
Cordless Rotary Hammer
Production code
Battery voltage
No-load speed
Rate of percussion under load max.
Impact energy per stroke according to EPTA-
Procedure 05/2009
Drilling capacity in concrete
Drilling capacity in steel
Drilling capacity in wood
Core cutter in concrete, bricks and limestone 65 mm
Chuck neck diameter
Weight according EPTA-Procedure 01/2003
(Li-lon 5,0 Ah)
Noise information
Measured values determined according to EN 60745. Typically, the
A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) 90,7 dB (A)
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!

Vibration information

Vibration total values (triaxial vector sum) determined according
to EN 60745
Hammer-drilling into concrete: Vibration
emission value a
h,HD
Uncertainty K=
Chiselling: Vibration emission value a
Uncertainty K=
WARNING!
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in EN
60745 and may be used to compare one tool with another. It may
be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for di erent
applications, with di erent accessories or poorly maintained, the
vibration emission may di er. This may signi cantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched o or when
it is running but not actually doing the job. This may signi cantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the e ects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING!
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock,
re and/or serious injury. Save all warnings and instructions
for future reference.
HAMMER SAFETY WARNINGS
Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
M18 CH
4565 55 02 ...
... 000001-999999
18 V
0 - 1400 min
-1
0 - 4900 min
-1
2,5 J
26 mm
13 mm
28 mm
43 mm
3,4 kg
101,7 dB (A)
8,9 m/s
2
1,5 m/s
2
9,5 m/s
2
h,Cheq
1,5 m/s
2
contact hidden wiring. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Additional Safety and Working Instructions
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is recom-
mended, such as dust mask, protective gloves, sturdy non-slip
footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Chips and splinters must not be removed while the machine is
running.
When working in walls ceiling, or oor, take care to avoid electric
cables and gas or waterpipes.
Remove the battery pack before starting any work on the appliance.
WARNING! To reduce the risk of re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in uid or al-low a uid to ow inside them.
Corrosive or conductive uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., Can
cause a short circuit.
Use only System M18 chargers for charging System M18 battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
SPECIFIED CONDITIONS OF USE
The battery rotary pneumatic hammer can be used for hammer
drilling and drilling in wood, metal as well as plastic for indepen-
dent use away from mains supply.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
but
For an optimum life-time, the battery packs have to be fully
charged, after use.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days: Store the battery
pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition Every six
months of storage, charge the pack as normal.
Do not dispose of used battery packs in the household refuse or
by burning them. Milwaukee Distributors o er to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it o immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
GB

English

15