Makita RP1802F Manuel D'instructions page 9

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Collet chuck capacity
Plunge capacity
No load speed
Overall height
Net weight
Safety class
Lamp
Speed adjusting dial
Electric brake
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The net weight value includes the attachment(s) for normal and safe use which are specified in the instruction
manual.
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-17:
Model RP1802
Sound pressure level (L
Sound power level (L ) : 96 dB (A)
WA
Uncertainty (K) : 3 dB (A)
Model RP1802F
Sound pressure level (L
Sound power level (L ) : 96 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model RP1803
Sound pressure level (L
Sound power level (L ) : 96 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model RP1803F
Sound pressure level (L
Sound power level (L ) : 96 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model RP2302FC
Sound pressure level (L
Sound power level (L ) : 99 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model RP2303FC
) : 88 dB (A)
pA
) : 88 dB(A)
pA
) : 88 dB(A)
pA
) : 88 dB(A)
pA
) : 91 dB(A)
pA
RP1802 RP1802F RP1803
-1
23,000 min
312 mm
-
-
-
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
can also be used in a preliminary assessment of
exposure.
WARNING:
WARNING:
use of the power tool can differ from the declared
total value(s) depending on the ways in which the
tool is used.
WARNING:
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The continuous vibration total value (tri-axial vector
sum) determined according to EN62841-2-17:
Model RP1802
Work mode: cutting grooves in MDF
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model RP1802F
Work mode: cutting grooves in MDF
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model RP1803
9 ENGLISH
RP1803F RP2302FC
12 mm or 1/2"
0 - 70 mm
-1
22,000 min 9,000 - 23,000 min
6.2 kg
/II
-
-
) : 91 dB(A)
pA
) : 99 dB (A)
WA
Wear ear protection.
The noise emission during actual
Be sure to identify safety mea-
2
) : 5.1 m/s
h
2
2
) : 5.1 m/s
h
2
RP2303FC
-1
327 mm