R&G CP0605 Instructions De Montage
Les langues disponibles
Les langues disponibles
Liens rapides
Page 1 of 8
CP0605
FITTING INSTRUCTIONS CP0605 APEX CRASH PROTECTORS
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
Racing Technique Ltd T/A R&G
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
Manuels Connexes pour R&G CP0605
Sommaire des Matières pour R&G CP0605
- Page 1 Page 1 of 8 CP0605 FITTING INSTRUCTIONS CP0605 APEX CRASH PROTECTORS HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
- Page 2 Page 2 of 8 CP0605 TOOLS REQUIRED GENERAL TORQUE SETTINGS M4 BOLT = 8Nm 8mm HEX KEY BIT • M5 BOLT = TORQUE WRENCH (UP TO 50Nm) • M6 BOLT = SUITABLE SUPPORT JACK • M8 BOLT = 20Nm 0 BOLT = 40Nm...
- Page 3 Page 3 of 8 CP0605 FITTING PICTURES Picture 1 Picture 2 FITTING INSTRUCTIONS Before removing engine bolts, ensure the bike is upright and supported by a suitable engine stand or jack placed under the sump of the motorbike to support the partial weight of the engine, this will prevent the engine from moving during fitting.
- Page 4 Page 4 of 8 CP0605 CONSUMER NOTICE The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
- Page 5 Page 5 of 8 CP0605 NOTICE DE MONTAGE CP0605 PROTECTIONS CRASH E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N...
- Page 6 Page 6 of 8 CP0605 OUTILS REQUIS VALEURS DE SERRAGE M4 BOULON = 8Nm CLÉ HEXAGONALE 8mm • M5 BOULON = 12Nm CLÉ DYNAMOMÉTRIQUE (JUSQU'À 50 Nm) • M6 BOULON = 15Nm CRIC DE SUPPORT ADAPTÉ • M8 BOULON = 20Nm...
- Page 7 Page 7 of 8 CP0605 PHOTOS DE MONTAGE Photo 1 Photo 2 NOTICE DE MONTAGE Avant de retirer les boulons du moteur, assurez-vous que la moto soit en position verticale et soutenue par un support moteur adapté ou un cric placé sous le carter d'huile afin de supporter une partie du poids du moteur.
- Page 8 Page 8 of 8 CP0605 ISSUE 1 - 09/02/2026 (MH) AVIS AUX CONSOMMATEURS La description du catalogue et les échantillons présentés ne constituent que des indications générales sur les Produits. R&G se réserve le droit d'apporter des modifications de conception qui n'altèrent ni leurs performances ni leur aspect esthétique.