Installation Requirements; Tools And Parts; Options; Location Requirements - Whirlpool WFC7500 Guide D'utilisation Et D'entretien

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Tools and Parts

Gather the required tools and parts before starting installation.
The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses
Pliers (that open to 1⁹⁄₁₆" [39.5 mm])
Flashlight (optional)
Tools needed for installation
Open end wrenches 13 mm and 12 mm
Level
Wood block
Ruler or measuring tape
Parts supplied
A
D
A. U-shaped hose form
B. Water inlet hoses (2)
C. Inlet hose washers (4)
D. Beaded tie strap
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free
number on the cover or in the "Assistance or Service" section.
If You Have
You Will Need to Buy
Laundry tub or
Sump pump system (if not already
standpipe taller
available)
than 55" (1.4 m)
Overhead sewer
Standard 20 gal. (76 L), 30" (76.2 cm) tall
drain tub or utility sink and sump pump
(available from local plumbing suppliers)
Floor drain
Siphon break, Part Number 285834;
additional drain hose
Part Number 8318155; and connector kit,
Part Number 285835
Drain hose too
4 ft (1.2 m) drain hose extension kit,
short
Part Number 285863
Water faucets
2 longer water fill hoses:
beyond reach of fill
6 ft (1.8 m) Part Number 76314
hoses
10 ft (3.0 m) Part Number 350008
4

INSTALLATION REQUIREMENTS

B
C
Pedestal
You have the option of purchasing a pedestal for this washer. You
may select an 11.8" (30.0 cm) pedestal. The pedestal will add to
the total height of the washer.
Optional pedestal
Pedestal
Approximate
Height
Height with
Washer
11.8" (30.0 cm)
44.7" (113.5 cm)
Stack Kit
Are you planning to stack your washer and dryer? To do so you
will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your washer
or refer to the "Assistance or Service" section. Ask for Part
Number W10178021.

Location Requirements

Selecting the proper location for your washer improves
performance and minimizes noise and possible washer "walk."
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. See "Drain
System."
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need
A water heater set to deliver 120°F (49°C) water to the washer.
A grounded electrical outlet located within 5.4 ft (1.65 m) of
where the power cord is attached to the back of the washer.
See "Electrical Requirements."
Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6 kPa).
A level floor with a maximum slope of 1" (2.5 cm) under entire
washer. Installing the washer on soft floor surfaces, such as
carpets or surfaces with foam backing, is not recommended.
A sturdy and solid floor to support the washer with a total
weight (water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in
low temperatures.

Options

Color
Model
Number
White
LAB0050PQ

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Duet sportDuet sport wfw8200tw

Table des Matières