Intended Use; Technical Data; Before Starting The Equipment - EINHELL GE-CC 18 Li Mode D'emploi D'origine

Separately available accessories
18V 1.5Ah P-X-C lithium-ion battery
18V 2.0Ah P-X-C lithium-ion battery
18V 2.6Ah P-X-C Plus lithium-ion battery
18V 3.0Ah P-X-C lithium-ion battery
18V 4.0Ah P-X-C lithium-ion battery
18V 5.2Ah P-X-C Plus lithium-ion battery
18V P-X-C Dual Port Fast Charger
18V P-X-C Fast Charger
Explore battery + charger options at
einhellUSA.com

3. Intended use

The equipment is designed to remove weeds
from between paving stones and slabs. It is not
intended for use on sensitive surfaces like tiles.
Equipment designed for use in private and
hobby gardens is regarded as unsuitable for
use in public facilities, parks and sports centers,
along roadways, or in agriculture and forestry.
The operating instructions as supplied by the
manufacturer must be obeyed to ensure that the
equipment is used properly.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............................18 V
No load speed: ........................... 1200 rpm (min
Brush diameter: .............................4 in. (100 mm)
Weight (Tool Only): ........................... 4.4 lbs (2 kg)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Anl_GE_CC_18_Li_USA_SPK7.indb 10 Anl_GE_CC_18_Li_USA_SPK7.indb 10
EN
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).

5. Before starting the equipment

5.1 Assembly (Fig. 3-7)
Connect the upper part of the housing and the
bottom part of the housing together (Fig. 3). Slot
the guide wheel (Fig. 4/Item 7) into the guide
on the housing (Fig. 4/Item 14). Make sure that
there is an audible click when they engage. Fit
the guard hood (Fig. 5/Item 6) as shown in Fig. 5
and secure with 2 screws (Fig. 5/Item. 15). Attach
)
-1
the brush (Fig. 6/Item 15) to the drive axle (Fig. 6/
Item 16). Make sure that the brush fi ts accurately
into the mount (Fig. 6/Item 17). The shaft must be
fi xed in order to fasten the brush. To do so, insert
the pin (Fig. 2/Item 10) into the recess on the
shaft (Fig. 7) and hold with one hand. Using the
open-ended wrench (Fig. 2/Item 11), tighten the
nut (Fig. 7/Item 12).
- 10 -
13.02.2020 13:05:42 13.02.2020 13:05:42