Personal Protective Equipment - Husqvarna 120i Manuel D'utilisation

• Stop the product and engage the chain brake before
you move the product. Hold the product with the
guide bar and saw chain pointing rearward. Put on a
transportation guard on the guide bar before
transportation or before you move it for any distance.
• When you put the product on the ground, engage the
chain brake and have a constant view of the product.
Stop the product and remove the battery before you
leave your product for any length of time.
• There is a risk that wood chips get stuck in the drive
system. This can cause the saw chain to get stuck.
Always stop the product and remove the battery
before you clean it.
• The vibration level increases if you cut with cutting
equipment that is incorrect or not correctly
sharpened. Cutting hardwoods, such as broadleaf
trees, causes more vibration than cutting softwoods,
such as conifers.(Fig. 28)
• Overexposure to vibration can lead to circulatory
damage or nerve damage in persons who have
decreased circulation. Speak to your physician if you
experience symptoms of overexposure to vibration.
Such symptoms include numbness, loss of feeling,
tingling, pricking, pain, loss of strength, changes in
skin colour or condition. These symptoms usually
occur in the fingers, hands or wrists increases in cold
temperatures.
• Do not try a pruning or limbing operation in a
standing tree unless you have special training.
• Always stand on the uphill side of the log when you
cut on a slope as the tree is likely to roll or slide
downhill after it is felled. To maintain complete
control of the product when you cut, release the
cutting pressure near the end of the cut. Do not relax
your hands around the handles. Do not let the saw
chain to touch the ground. After you have completed
the cut, wait for the saw chain to stop before you
move the product. Always stop the motor before you
move from tree to tree.(Fig. 29)
• Do not fell a tree is there is any risk that it endangers
any person, strike or cause any utility line, or cause
property damage. If the tree strikes a utility line, the
utility company must be notified immediately.
• Make sure that you can move around safely.
Examine the conditions and the terrain around you
for possible obstacles such as roots, rocks,
branches, ditches and more. Be careful when you do
work on sloping ground.
• Prevent situations which you think is beyond your
capability.
• It is not possible to include each possible situation
you can face when you use this product. Always be
careful and use your common sense.(Fig. 30)

Personal protective equipment

WARNING: Read the warning instructions
that follow before you use the product.
1259 - 001 - 11.07.2019
(Fig. 31)
• Most chainsaw accidents occur when the saw chain
touches the operator. You must use approved
personal protective equipment during operation.
Personal protective equipment does not give you full
protection from injuries but it decreases the degree
of injury if an accident occurs. Speak to your
servicing dealer for recommendations about which
equipment to use.
• Your clothing must be close-fitting but not limit your
movements. Regularly do a check of the condition of
the personal protective equipment.
• Use an approved protective helmet.
• Use approved hearing protection. Long-term
exposure to noise can result in permanent damage
to the hearing.
• Use protective glasses or a face visor to decrease
the risk of injury from thrown objects. The product
can throw objects, such as wood chips, small pieces
of wood and more, at large force. This can result in
serious injury, especially to the eyes.
• Use gloves with saw protection.
• Use pants with saw protection.
• Use boots with saw protection, steel toe-cap and
non-slip sole.
• Always have a first-aid kit with you.
• Risk of sparks. Keep fire extinguishing tools and a
shovel near to prevent forest fires.
Safety devices on the product
WARNING: Read the warning instructions
that follow before you use the product.
• Do not use a product with defective safety devices.
• Do a check of the safety devices regularly. Refer to
Maintenance and checks of the safety devices on
the product on page 21 .
• If the safety devices are defective, speak to your
Husqvarna servicing dealer.
Keypad
The warning indicator flashes if the chain brake is
engaged or if there is a risk of overload. The overload
protection temporarily stops the product and you can not
use the product until the temperature restores. If the
indicator shows a solid light, turn to your servicing
dealer. (Fig. 32)
The automatic stop function
The product has an automatic stop function that stops
the product if you do not use it for one minute.
13