Intended Use; Residual Risks - Ryobi R18ROS Traduction Des Instructions Originales

Safety, performance, and dependability have been given
top priority in the design of your random orbital sander.

INTENDED USE

The random orbital sander is intended for sanding and
finishing metal, wood, plastic, or similar materials using
the abrasive pads provided. The random orbital sander is
intended to be used by adult operators who have read the
instruction manual and understand the risks and hazards.
The random orbital sander should only be used in well
ventilated areas. The random orbital sander is designed for
dry sanding only.
The random orbital sander is intended for consumer use
and should only be used as described above and not for
any other purpose.
WARNING
Dust from certain paints, coatings, and other materials
may cause irritation or allergic reactions. Dust from
wood, such as oak, beech, MDF, and similar materials
can be carcinogenic. Only qualified specialists should
be allowed to use the product on materials containing
asbestos.
WARNING
Do not use compressed air to remove dust from the
product. Dirt and grit blown away by compressed air can
cause serious eye injury.
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
RANDOM ORBITAL SANDER SAFETY WARNINGS
Always wear safety goggles and a dust mask when
sanding, especially sanding overhead.
A suitable breathing respirator must be worn while
sanding lead paint, some woods and metal to avoid
breathing the harmful/toxic dust or air. Contact with
or inhalation of dust produced from these materials can
endanger the health of operator and bystanders.
Do not throw sanding dust on an open fire because
materials in fine particle form may be explosive.
Do not use the product for wet sanding.
Do not use sanding paper larger than needed. Extra
paper extending beyond the sanding pad can also
cause serious lacerations.
When not in use, all tools should be disconnected from
power source.
Caution, fire hazard! Avoid overheating the object being
sanded as well as the sander. Always empty the dust
collector before taking breaks.
Protect the battery against heat (e.g., continuous
intense sunlight and fire), water, and moisture.
Properly dispose of dropped or damaged battery
immediately.
Clamp workpiece with
Unclamped workpieces can cause severe injury and
damage. Do not hold the material you are sanding by
hand.
Do not apply excessive pressure to the product.
ADDITIONAL BATTERY SAFETY WARNING
WARNING
damage due to a short circuit, never immerse your
as seawater, certain industrial chemicals, and bleach
or bleach containing products, etc., can cause a short
circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
Injury caused by dust
NOTE: Using the product will produce considerable
amount of dust and fine particles. Use the dust collection
device or connect a dust extraction vacuum when
operating the product. Wear dust masks containing
filters appropriate to the materials being worked on.
Ensure adequate workplace ventilation. Do not eat,
drink or smoke in the work area.
Injury caused by noise and vibration
NOTE: Wear ear protection during the sanding
operation. Do not operate the product for long periods
of time. See "Risk reduction".
EN
English
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
a clamping device.
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
1