Introduction; Device Description (Fig. 1−19); Scope Of Delivery; Proper Use - Parkside Pbts 370 B2 Instructions De Fonctionnement Et De Sécurité, Traduction Du Manuel D’utilisation Original

2. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment and suc-
cess.
Note:
In accordance with the applicable product liability laws, the
manufacturer of this device assumes no liability for damage to
the device or caused by the device arising from:
• Improper handling
• Failure to comply with the operating manual,
• Repairs carried out by third parties, unauthorised specialists.
• Installing and replacing non-original spare parts,
• Improper use
• Failures of the electrical system in the event of the electri-
cal regulations and VDE provisions 0100, DIN 57113 /
VDE0113 not being observed.
Note:
Read the whole text of the operating manual before assembly
and commissioning.
This operating manual should help you to familiarise yourself
with your device and to use it for its intended purpose.
The operating manual contains important information on how
to operate the product safely, professionally and economically.
This helps you to avoid danger, costly repairs, reduce down-
times and increase reliability and service life of the product.
In addition to the safety instructions in this operating manual,
you must also observe the regulations applicable to the opera-
tion of the device in your country.
Keep the operating manual at the device, in a plastic sleeve,
protected from dirt and moisture. They must be read and care-
fully observed by all operating personnel before starting the
work.
The device may only be used by personnel who have been
trained to use it and who have been instructed with respect to
the associated hazards. The required minimum age must be
observed.
In addition to the safety instructions and the separate regula-
tions of your country, the generally recognised technical rules
for operating machines of the same type must also be ob-
served.
We accept no liability for accidents or damage that occur due
to a failure to observe this manual and the safety instructions.
3. Device description (fig. 1−19)
1. Knurled screw for sanding belt adjustment
2. Support foot
3. Sanding belt tensioner
4. Grinding wheel
5. On/off switch
6. Transverse stop
7. Grinding table
8. Locking screw for sanding table
9. Angle scale
10. Suction port
11. Base plate
12. Allen screw
13. Grinding belt
14. Stop rail
15. Bottom disc guard
16. Screw for bottom disc guard
17. Allen screw
18. Screw for sanding belt guard
19. Sanding belt guard
20. Holder tube
21. Grinding belt holder
22. Transport handle

4. Scope of delivery

• 1 belt and disc sander
• 1 transverse stop
• 1 sanding table
• 1 sanding belt P80 (pre-assembled)
• 1 sanding disc P80 (pre-assembled)
• 1 Allen key
• 1 Operating manual

5. Proper use

The purpose of the belt and disc sander is to sand all types of
wood, depending on the size of the machine.
The machine complies with the applicable EC machinery direc-
tive.
• The safety, operating and maintenance specifications of the
manufacturer, as well as the dimensions specified in the tech-
nical data, must be observed.
• The applicable accident prevention regulations and the oth-
er generally accepted safety rules must be observed.
• The machine may only be used, maintained or repaired by
competent persons who are familiar with it and have been
informed of the dangers. Any liability of the manufacturer for
damages resulting from arbitrary changes to the machine is
excluded.
• The machine may only be operated with original accessories
and original tools from the manufacturer.
• Any use beyond this is improper use. The manufacturer is not
responsible for the resultant damages, the user bears this
risk alone.
Please observe that our equipment was not designed with the
intention of use for commercial or industrial purposes. We as-
sume no guarantee if the equipment is used in commercial or
industrial applications, or for equivalent work.
GB/IE 3