Weitere Sicherheitshinweise - WOLFF BS 180 Traduction Du Mode D'emploi Original

b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power
tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to the
wheel's movement at the point of snagging.
d) Use special care when working corners,
sharp edges etc.Avoid bouncing and snagging the
accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of control.
4.3 Safety Warnings Specific for Grinding
and Abrasive Cutting-Off Operations:
a) Use only wheel types that are recommended for
your power tool and the specific guard designed for
the selected wheel.
Wheels for which the power tool was not designed cannot
be adequately guarded and are unsafe.
b) The grinding surface of the centre depressed
wheels must be mounted below the plane of the guard
lip.
An improperly mounted wheel that projects through the
plane of the guard lip cannot be adequately protected.
c) The guard must be securely attached to the power
tool and positioned formaximumsafety, so the least
amount of wheel is exposed towards the operator.
The guard helps to protect operator from broken wheel
fragments and accidental contact with wheel and sparks
which could ignite clothing.
d) Always use undamaged wheel flanges that are of
correct size and shape for your selected wheel.
Proper wheel flanges support the wheel thus reducing the
possibility of wheel breakage. Flanges for cut-off wheels
may be different from grinding wheel flanges.
e) Do not use worn down wheels from larger power
tools.
Wheel intended for larger power tool is not suitable for the
higher speed of a smaller tool and may burst.
4.4 Safety Warnings Specific for Grinding
with Diamond Cup Wheels:
a) Always use undamaged wheel flanges that are the
correct size and shape for your selected accessories.
The correct flanges support the accessories.
4.5

Weitere Sicherheitshinweise:

WARNING – Always wear protective
goggles.
Wear a suitable dust protection mask.
Do not use bonded discs.
Use elastic cushioning layers if they have been
supplied with the grinding media and if required.
Observe the specifications of the tool or accessory
manufacturer! Protect the discs from grease or
impacts!
Never use cutting discs for roughing work! Do not apply
pressure to the side of the cutting discs.
If accessories with threaded inserts are used, the
end of the spindle may not touch the base of the
hole on the grinding tool.
Make sure that the thread in the accessory is long
enough to accommodate the full length of the spindle. The
thread in the accessory must match the thread on the
spindle. (Technical Data).
Observe the specifications of the accessory
manufacturer! Protect the accessories from grease
and physical impact.
Accessories must be stored and handled with care
in accordance with the manufacturer's instructions.
Secure small workpieces. For example, clamp in a
vice.
The workpiece must lay flat and be secured against
slipping, e.g. using clamps. Large workpieces must be
sufficiently supported.
Damaged, eccentric or vibrating tools must not be
used. Only use accessories that are surmounted
by brushes of the safety guard.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
Read the operating instructions supplied with the
installed angle grinder.
Use of a fixed extractor system is recommended. Always
install an RCD with a max. trip current of 30 mA upstream.
If the anglegrinder is shut down via the RCD, it must be
checked and cleaned.
See chapter Cleaning.
S-automatic safety clutch. When the safety clutch
responds, switch off the machine immediately!
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
A damaged or cracked safety guard must be replaced.
Never operate a machine with a defective safety guard.
Secure small workpieces. For example, clamp in a vice.
- 13 -