Table des Matières
Publicité
10 | English
Do not vacuum or blow any liquids. The penetration of
u
liquids increases the risk of an electric shock.
Ensure that the workplace is well ventilated.
u
Do not let children use the power tool unsupervised.
u
Children are at risk of injuring themselves this way.
Wear additional personal protective equipment such
u
as protective glasses and a protective mask. Wearing
personal protection equipment appropriate to the condi-
tions reduces your exposure to hazardous substances.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Do not expose power tools to rain or wet conditions.
u
Water entering a power tool will increase the risk of elec-
tric shock.
If operating a power tool in a damp location is un-
u
avoidable, use a residual current device (RCD) protec-
ted supply. Use of an RCD reduces the risk of electric
shock.
Never use the power tool if the cable is damaged. Do
u
not touch the damaged cable and pull out the mains
plug if the cable is damaged while working. Damaged
cables increase the risk of an electric shock.
Do not crush the cable or run the device over it. Do not
u
pull on the power cable to pull the plug out of the
socket or to move the power tool. Damaged cables in-
crease the risk of an electric shock.
Pull the plug out of the socket before adjusting the
u
tool settings, changing accessories, or storing the
power tool. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
1 609 92A 59F | (26.10.2020)
Intended Use
The power tool is intended for vacuuming and blowing sub-
stances that are not hazardous to health.
The power tool is not suitable for vacuuming and blowing
flammable materials, metal chips and sharp objects such as
screws or nails.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Handle
(2) On/off switch
(3) Lock-on button for on/off switch
(4) Thumbwheel for adjusting airflow
(5) Air outlet
(6) Caps for carbon brushes
(7) Nozzle
(8) Dust bag
(9) Air inlet
(10) Carbon brushes
Technical Data
Blower
Article number
Rated power input
Air volume
Air pressure
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according to
EN 62841-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 89 dB(A); sound power level
100 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 62841-1:
2
2
a
< 2.5 m/s
, K = 1.5 m/s
,
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
GBL 82-270
GBL 800 E
3 601 J80 4..
W
820
3
m
/min
4.5
mbar
0–72
kg
1.8
/ II
Bosch Power Tools
Publicité
Table des Matières
