Before Operating; While Operating; Maintenance And Cleaning - VITO WR1 115B PRO-POWER Mode D'emploi

EN
The use of extensions to connect the
power cord is not recommended.
However, if you use an extension, you
should have some care, such as:
� If using the machine outdoors, use only
suitable extension cords for outdoor
use. The use of a suitable extension
cord reduces the risk of electric shock;
� Use only extensions, plug and sockets
with earth connection;
� The extension cable section must
be proportional to its length and have
similar or superior features of the
machine's power cable;
� Do not use damaged extensions.
Check the extension before use and
replace it if necessary;
� When the extension is in the form of a
coil, unroll the entire cable;
� Always unplug the extension from the
electrical outlet before removing the
machine's plug;

2.3 - BEFORE OPERATING

Make sure that the machine is used
only by who is familiarized with the
instruction manual.
To ensure a safe operation, you must
take certain cares and procedures into
consideration:
� Inspect the machine before each
use. Make sure that the attached
accessories are properly assembled
and in good condition. If excessive
wear or damage occurs, replace the
accessories.
� Make sure all tightening screws are
properly fastened. A regular overhaul
is important to ensure safety and good
performance;
� Check if the safety devices are in
perfect condition and
correctly. Never operate the machine
if the safety devices are missing,
inhibited, damaged or worn;
� Make sure that the "ON/OFF" switch
is off when you connect the power
cable. If the switch is damaged or does
not allow to control the machine, it
must be repaired or replaced in order
to avoid unintentional starts;
Perform all necessary adjustments to
the correct assembly of the machine,
and in case of having any questions or
problems, contact your official dealer.

2.4 - WHILE OPERATING

Keep third parties away from the
work area. Never operate the
machine while animals or people,
particularly children, are at risk.
Place the machine on a firm, flat floor
to prevent movement during operation.
Always wear
equipment. The use of face shields or
goggles, dust masks, ear protection,
non-slip safety footwear, long-sleeved
clothing, gloves and helmets under
proper conditions, reduces the risk of
injury.
When operating, place yourself in
a stable position and always keep
balance. Hold the gun firmly to ensure
a continuous operation and withstand
unexpected situations.
Do not cover the machine during
use or use it in spaces without
adequate ventilation. To avoid the risk
of overheating, keep the ventilation
openings
unobstructed to allow air circulation.
Do not use the machine for long
periods of time or expose it to the sun.
Such conditions cause overheating,
which leads to a constant activation of
the machine's thermal protection.
Operating the machine with a supply
voltage lower than the recommended
in the technical specifications or using
extensions with a very long cable can
functioning also cause a constant activation of the
thermal protection.
While using the machine, plan some
personal protective
permanently clean and
breaks and avoid using it for long
periods of time. Permanent vibrations
are harmful to health.
A massive load of vibrations may
damage nervous and
systems, especially to whom have
circulatory problems. Inform your
doctor if any symptoms arise caused
by vibration. Among these symptoms,
that occur specially on fingers, hand
and wrists, are also included loss of
sensation, pain, muscle weakness, skin
discoloration or tingling sensation.
2.5 - MAINTENANCE AND
CLEANING
Before cleaning, adjusting, replacing
accessories, repairing or maintenance
works, the power cord must be
unplugged from the electrical outlet.
Replace every worn or damaged part
immediately, so that the machine
is always in a safe and operational
condition.
Cleaning:
The equipment must be well cleaned
after use.
Do not use aggressive
products. These products can damage
plastics and metals, leading to an
incorrect operation of the machine.
Maintenace:
Only maintenance works described
in this instruction manual may be
performed; all other work must be done
by an official distributor.
Keep all nuts and screws well tightened
so the machine is always in good and
safe conditions of operation.
The maintenance of this type of machine
requires extreme care and knowledge
of its system, and should be carried
out only by a qualified technician.
The replacement of components of a
machine with double insulation should
be done with the same original parts.
circulatory
cleaning
27