Safety Features Of The Device; Choosing The Correct Constriction Ring; Choosing A Transfer Sleeve - Owen Mumford Rapport Classic Mode D'emploi

The Rapport™ Classic V.T.D. is a complete system with everything you
need for immediate use.
Inside the discreet storage bag you will find:
1
Five sizes of Rapport™ constriction rings.
1
Five numbered rings vary in size. Number 4 is
the smallest ring and Number 8 is the largest.
The center ring is designed to encircle the base
of the penis. The outside rings serve as handles
for easy application and removal.
2
An easy to use Vacuum Pump which has a
2
specially angled handle to make creating the
erection simple.
As a safety measure the vacuum pressure
is controlled by a valve that will not allow
the pressure to raise above 360mm of Hg.
The vacuum pressure can be released at
any time by pressing the pressure release
3
valve on the top of the pump.
3
A loading cone to assist the mounting of the
constriction rings onto the transfer sleeve.
4
A penile tube in durable clear material, which
attaches to the pump unit at one end and the
4
transfer sleeve with the constriction ring at
the other.
5
Two transfer sleeves, which give a choice of
internal diameter. Both are specially shaped to
hold the constriction ring and make it easy
to transfer the ring onto the base of the penis.
6
A tube of water soluble lubricating jelly. This helps
5
to create the vacuum seal and prevent the penis
from adhering to the penile tube.
7
A constriction ring sizing guide for easy selection
of the correct size ring and a warranty card. These
can be found at the back of this instruction book.
8
An instruction DVD, which shows how to put
6
the Rapport™ Classic V.T.D. together and
demonstrates how to create an erection. A live
model is used in the DVD which may be offensive
to some people.
7
8
8

Safety Features of the Device

Special safety features have been included into the Rapport™ Classic
V.T.D. to make it as safe to use as possible.
The vacuum pump. This has been designed so that it cannot reach a
dangerously high pressure no matter how hard you press the pump. Any
excess pressure is automatically released through the pressure release
valve. This helps to prevent bruising of the penis particularly when first
using the Rapport™ Classic V.T.D.
The pressure release valve. This allows the vacuum pressure in the
penile tube to be immediately released when the valve knob is pressed
down. The valve knob is situated near the pump handle and should be
pressed at any time when pain is felt in your penis as you are creating
the erection.
The penile tube. This is made from clear plastic so that it is possible
to see your erection developing inside the tube. This helps to give you
confidence in the working of the vacuum pump.
The transfer sleeves. These are made from a soft material for comfort
against your skin and are specially shaped to allow the constriction ring to
slide down onto the base of the penis with as little discomfort as possible.
The constriction rings. These are made of a soft material for comfort
and ease of use. The two outer handles make the ring easy to move
when loading it onto the transfer sleeve and removing from the penis
after intercourse. They can be used for the speedy removal of the ring
from the penis if this is necessary at any time.

Choosing the Correct Constriction Ring

One of the most important parts of the Rapport™ Classic V.T.D. is the
constriction ring. The ring must encircle the penis and fit comfortably tight.
The constriction ring works by retaining the blood in the penis to maintain
a firm erection.
Using the constriction ring sizing guide provided, place your flaccid (non
erect) penis into the slots until you find one which fits the circumference of
your penis. Each slot has a ring size marked above it which corresponds
to the ring you require.
If the Rapport™ Classic V.T.D. gives you a good erection, and with the
constriction ring on your penis, your erection becomes soft within five
minutes or less, you will need to try a ring one size smaller.
If the constriction ring seems too tight, next time use one size larger to see
if it will maintain your erection. Try different sizes until you are satisfied with
their fit. There are 5 sizes to choose from.

Choosing a Transfer Sleeve

There are two transfer sleeves provided with two internal diameters.
Depending on the size of your penis you should choose which of the two
is likely to be the most suitable. Remember that your erect penis will need
to be withdrawn through the transfer sleeve.
The transfer sleeves are specially shaped so that the constriction ring
can be easily loaded and held in the flat groove.
9