Dimplex DF2624L-INT Manuel D'installation page 5

Controls : See Fig. 2
Display Function
Icon
Power
Standby
Sleep
Timer
Flame Effect
Low
Flame
High
c
Flame
Demo
Mode
Off
Log
Effect
Heat
Low Heat
E ßß ß —
— ßßß
High
Heat
Cool
Blow
Off
Temp
Down
Temp Up
User Modes:
Mode Name [Discription
Change Celsius (c C) to Fahrenheit
Disable/Enable Heat Options
Description
Press once to turn the product
Press a second time to put the product
/
(When returning from 'STANDBY' mode the product will return to previous settings unless the product
has been plugged out, in which case it will reset to factory settings)
Press multiple times to change
off. The remaining time on the 'SLEEPTIMER' displays. (This icon is Green in Colour)
'FLAME EFFECT' button cycles the unit sequentially
DEMO MODE and OFF.
Thissetting will run the flame effect at a low brighness level. (The display will show Fl )
Thissetting will run the flame effect at a high brighness level. (The display will show F2)
Thissetting will slowly pulse the flame effect between low and high brightness. (The display will show
Thiswill turn the flame effect off. If the heater is running, the display will activate and remain active to
read the set temperature
Press this button to turn the log LED 'ON' and 'OFF'
'HEAT' button cycles the unit sequentially
and OFF. The heat setting will be indicated
When the flame effect is 'ON' the floating display will turn off after 5 seconds. however if the heater is
being used independantly
in the floating display.
Thissetting will run the heater at 'LOW HEAT' this setting will be indicated by the 'LOW HEAT' icon
and the letters 'LO' appearing
(This icon is Orange in Colour)
This icon in the floating display indicates
icon and the letters 'HI' appearing
(This icon is Red in Colour)
This icon in the floating display indicates
BLOW' icon and the letters 'CB' appearing
(This icon is Blue in Colour)
This switches the heater and blower
blower will run for 10-20 seconds after being turned off this is to ensure the product
Press multiple times to lower the heater temperature
can be set SC.
Note: Once you stop at your desired temperature
room temperature as detected
room temperature the heater will not activate.
Press multiple times to increase
that can be set 37 oc.
Note: Once you stop at your desired temperature
room temperature as detected
room temperature the heater
Action (Actions cannot
Press both Temp u p(+0 andTemp d own (1¯)ontheunit a ndhold until beep isheard
(0 F)
and display flashes. (To revert back to Celsius repeat this action)
Hold both Heat B utton ( L) andFlame Button
heater has been disabled
action.
'ON',
into 'STANDBY'
the 'SLEEPTIMER' in 0.5 hr increments
through
and show if the product is on LOW HEAT/ HIGH HEAT/COOL BLOW.
through the 4 settings: LOW HEAT. HIGH HEAT, COOL BLOW
by an icon in the floating display see Fig. I.
of the flame effect. The low heat or high heat icon will appear
in the display.
'HIGH HEAT' this setting will be indicated
in the display.
'COOL BLOW' this setting will be indicated
in the display.
'OFF' no icon will be displayed
in IOC increments.
this will flash 3 times. then the display will show the
by the product. If the set temperature
the heater temperature
this will flash 3 times, then the display will show the
by the product. If the set temperature
will not activate.
be input by remote control)
the display will read "--1' and beep. To enble heat repeat
from 0.5 hr to 8.0 hr before turning
the 4 setting, LOW FLAME, HIGH FLAME,
by the 'HIGH HEAT'
by the 'COOL
in the floating display. Note the
cools down safely.
The lowest temperature
is lower than the detected
in IOC increments. The highest temperature
is lower than the detected
ontheunit. f or2seconds, when the
continuously
that
this