Trimmer/Edger; Trimmer; Starting Edger/Trimmer; Trimming - Remington Rm40Bst Manuel Du Propriétaire

TRIMMER/EDGER

OPERATING THE

TRIMMER/

EDGER

A WARNING:
Read and understand
owner's manual before operat-
ing trimmer/edger. Make certain
you read and understand
Safety Warnings of this manual.
Improper use of this trimmer/
edger can result in severe
jury or death from fire, electric
shock, or body contact
moving parts.
A WARNING:
The trimmer/edger can throw
debris, causing injury
nearby.
• Wear approved eye protec-
tion, long pants, and shoes
while operating this tool
A WARNING:
Keep away from
line and cutting head while
trimmer/edger is running.
Contact with cutting line can
cause serious injury.
Keep cutting head
from your hands and feet
and bystanders when
use.
Keep cutting guard in place
and in proper working
der.
Wear long pants and shoes
while operating this
mer/edger.
Stop trimmer/edger
servicing or examining
power head.
ADJUSTING SHAFT LENGTH
- CONVERTING TO EDGER/
TRIMMER
Adjustments to length and location of the
cutting head is pelformed by gripping the
shaft collar with one hand
housing with the other. (See Figure 14)
NOTE: Wrenches and pliers are not re-
quired for shaft adjustment
never be used.
2. To adjust pole height up and down, hold
collar and TWIST motor housing 900
OPERATION
COUNTER
3. When desired
TWIST motor houusing
WISE to lock in place.
NOTE: Shaft has internal limits to stop
this
rotation
position.
4. For edger function, hold col lar and TWIST
all
motor housing 1800 to lock into position.
in-
with
Trimmin
to those
Figure 14 - Adjusting
STARTING
EDGER
Basic Trimmer
As a safety feature. this trimmer/edger requires
the trigger lockout button to be drepressed prior
to squeezing the trigger. (See Figure 15)
cutting
Trigger Lock- Trigger Switch
out utton
away
Figure 15 - Front and rear trigger
in
This tool is designed to trim grass and weeds
with ease. Follow the steps below to start and
stop the trimmer.
or- I . Place fully charged battery in trimmer.
(See Figure 16)
2. Hold the front handle with one hand. (See
Figure 17)
trim-
before
Figure 16 - Placing
and the motor
and should
Figure 17 - Positioning
handle.
CLOCKWISE.
pole height is reached,
900 CLOCK-
- this is considered the locked
Ed in
shaft length
THE TRIMMER/
Operation
switches
battery in trimmer
hand on front
9
3. While grasping the rear handle, with the
other hand. depress the trigger lockout
button. (See figure 18)
4. Squeeze trigger, the trimmer
immediately. (See Figure 19)
5. While squeezing trigger, release trigger
lockout button. Trimmer will
6. To stop the trimmer, release the trigger.
The trimmer will coast to a stop.
Figure 18 - Depress lockout button
squeeze trigger
Figure 19 - Release lockout button

TRIMMING

To reduce excessive line wear and improve
trimming performance, follow the steps below
to trim grass and weeds.
Remove any string, wire, or other materials
that could become entang ed in the trim-
mer/edger from the trimming area.
2. Hold trimmer/edger using both front and
rear handles (See Figure 20).
3. Slowly sweep the trimmer/edger flom side
to side or front to back.
4. Do not force the trimmer/edger.
only the tip of the trimmer/edger
cut the grass or weeds.
5. If grass or weeds are tall, cut them in
several increments, staning from the top
and working to the bottom.
Figure 20 - Holding trimmer/edger
will start
remain on.
and
Allow
line to