neofeu NL2012R Mode D'emploi page 6

for use for each component of the system and
with the norms: EN353-1 / EN353-2 / EN 355 /
EN360 / EN 362. For mobile fall arresters that
include a rigid fall prevention support (EN353-1)
or a flexible one (EN353-2), it is recommended to
connect the harness to the sternum anchoring.
For the energy absorbers (EN355) or fall
arresters with automatic return (EN360), connect
the harness instead to the dorsal anchorage.
- The anchor point on the structure to which the fall
prevention system is fixed must be right above
the user and have a static strength of at least 10
kN. It must also meet the requirements of
standard EN795. Do not deviate too much from
the plumb line of this anchoring in order to limit
the scope of a possible pendulum drop.
- After a fall, the lanyard should be destroyed and
replaced.
- Use of the lanyard with connectors equipped with
a clasp with automatic closure and manual
locking is not recommended except in cases
where the user does not have to open and close
the connector frequently, which is to say several
times during a workday. If this is the case, it
would be preferable to use a connector with
automatic locking.
- A connector should never be stressed at its clasp.
GENERAL CONDITIONS FOR UTILIZATION:
- Periodic inspections carried out by a competent
inspector are necessary in order to ensure the
safety of the user, which is related to maintaining
the effectiveness and the resistance of the
equipment. An annual required inspection will
validate the condition of the equipment, and it
can only be kept in service if it receives written
approval.
- Do not expose these products to temperatures
below –35°C or above 50°C.
- Use of this equipment cannot be diverted and in
no case can it be pushed beyond its limits.
- Storage: the product must be stored in a dry and
aerated place, protected from any direct or
indirect heat source, and from ultra-violet rays.
LABELING OF PRODUCT:
- The name of the equipment: Work-positioning lanyard.
Reference for the Lanyard: Type: ...
-
Series Number: N°...
-
Lot Number: Lot: ...
-
Lanyard Material:
-
Year of Manufacture: Year: ...
-
The EC logo followed by the number from the
-
agency to be notified and which is to be involved
in the monitoring phase of production: CE0333.
The pictogram that directs the user to read the
-
GB
The drying of wet equipment must be under the
same conditions.
- Cleaning and disinfecting: exclusively with water
or with neutral soap.
- Packaging: use protective packaging that is tight
and rot-proof.
- Transportation: in wrapping and protected from
environmental impact or pressures.
- Any modification or repair of the product is
forbidden.
- Update the identification sheet and maintenance
record as of when it is put into service and during
each inspection.
- Life expectancy: PPE (personal protective
equipment) against falls from height
manufactured by Néofeu are designed for many
years of use under normal conditions of
utilization and storage. The life expectancy
depends on how it is utilized. Certain particularly
aggressive marine, siliceous, and chemical
environments can reduce the life expectancy of
PPE. In these cases particular attention must be
paid to protections and inspections before
utilization. The required annual inspection will
validate the correct functioning of the mechanism
and its being kept in service, which will only
occur with the written approval of the
manufacturer or his representative.
With regards to the preceding, the indicated life
expectancy recommended by Néofeu for the
products is ten years.
Agency for Notification for CE type
CETE APAVE SUD EUROPE N° 0082 – BP193 –
F13322 MARSEILLE Cedex 16
Agency for Notification to occur during
production monitoring phase:
AFAQ AFNOR Certification –
116, avenue Aristide Briand – BP40 –
F92224 BAGNEUX Cedex
manual before using the product: "i"
The manufacturer or dealer's logo along with
-
their contact information.
The number for the European standards with
-
which the equipment complies, along with its
validation date: EN... : ...
The Manufacturer's contact information
-
DEX NLMT 06 – M / 01 – page 6/16
inspection: