Publicité
ENGLISH
· TRANSLATION OF THE ORIGINAL
2) Adequate artificial lighting is required in work areas
when ambient light is insufficient.
3) Recommended operating temperature between 0
and 40°C and between 0.8 and 1.1 bar (maximum
humidity 95%).
4) Before starting operations, wear protective gloves,
hearing protectors and protective glasses.
5) When unpacking the machine, and also after each
use, check for dents or deformations and broken
parts and cords. If any of these are found, do not
use the electric tool and contact the manufacturer
immediately.
6) Do not use the mixer to work with flammable liquids
or gases, nor any material other than mortar or
cementitious adhesives. Furthermore, do not use
the tool if there are flammable liquids or gases in the
vicinity.
7) Hold the mixer firmly during use.
8) Keep the tool clean and free of grease, oil and dry
mortar or cement residue. Do not use aggressive
chemical products or solvents during cleaning. See
the "Cleaning and maintenance" section for more
information.
2.3 Work area
3.- OPERATING INSTRUCTIONS
3.1 Assembly instructions
After unpacking the machine, carefully check for
damaged or broken parts. If you find any damaged or
malfunctioning parts, replace them with original spare
parts from the manufacturer and contact RUBI's after-
sales service.
Mounting the mixing head.
1.
The mixer head comes disassembled from the mixer.
2.
Screw the upper part of the mixer head to the
output shaft (M14) of the RUBIMIX-7 MINIMAX.
(fig.1)
3.
Tighten the fixed 22 mm wrench. hard to screw the
mixing head , turning to the left and use the auxiliary
key of 22 mm. in the output shaft to fix the mixing
head , rotating clockwise. (fig.2)
Preflight
4.
Ensure that the voltage of the power supply
match the voltage and frequency indicated on the
nameplate of the machine. (fig.3)
5.
Machines can also be connected to 230V 210V /
240V. Machines can be connected to 110V 100V /
120. (fig.4)
6.
Only use mixer heads indicated in this manual with a
maximum diameter of 120 mm.
10
Work position
3.2 Staring the machine
Connection
7.
Before operating the machine enter the head in the
product mix. (fig.5)
8.
To start the mixer, press the ON switch. You will see
the mixer turn on gradually (fig.8).
8.1 If you want to lock the mixer in the on position,
press the lock button while holding the ON switch.
You can then release the ON switch and then the
lock button (fig.6).
8.2 Turn the speed dial to the desired speed. You
can adjust the speed while mixing to match the
specific needs of your recipe (fig. 12.1).
9.
Depending on the consistency of the material and
mixing amount should determine the various mixing
heads to be used.
If the product is a low viscosity mix use a mixing
head with a left hand helix. If instead product is
a high viscosity mix, use a mixing head propeller,
clockwise.
10. Always hold the machine with both hands, up and
down the mixer to remove.
Move the machine across the container during the
mixing process to ensure an even finish.
Attention! If while running the mixer it butts the
container surface, this could produce a strong kick.
Work the material until it has reached the proper
degree of mixture following the recommendations
given by the manufacturer of the materials.
The more viscous the material to be mixed, the
greater the strength of torque acting on the
machine.
11. Career so that revolutions can not drop abruptly and
reach stop the machine.
Disconnection
12. Release the on / off switch to turn off the machine.
The sound will continue for a while after being
turned off, so wait until the machine has completely
stopped before removing the mixing head of the
container.
If the mixer is locked in the ON position, press the
ON/OFF switch and then release it (fig. 12).
Changing the mixing head.
13. To change the mixing head, use the fixed 22 mm
wrench. and screw tightly, turning clockwise. (fig.9)
14. If the mixing head is stuck , use a 22mm wrench to
assist, placing it in the mixer shaft.
3.3 Cleaning and maintenace
WARNING! Unplug the plug before performing any
adjustments, repairs or maintenance. Cleaning and
correct maintenance of the machine extends the useful
life of its tools.
Immediately clean the machine and the mixer paddle
after each use.
Publicité
