Compatibility With Midland Bt Line Units; Pairing The Midland Btx2 Pro To Bluetooth Devices; Background Feature; Pairing With One Or Two Phones - Midland BTX2 PRO Guide D'utilisation

Compatibility with Midland BT line units

The BTX2 PRO is compatible with BTX1 PRO, BTNext PRO, BT Next Conference,
BTX2 FM and BTX2 FM.
When paired the max distance of the intercom is defined from the lower possible.
The BTX2 PRO is compatible with the previous line of Midland BT (BT Next, BTX2 and
BTX2) only if updated to firmware version 2014 or later.

Pairing the Midland BTX2 PRO to Bluetooth devices

The Midland BTX2 PRO unit can be paired to other Bluetooth devices, like Pho-
ne, GPS Navigator or PMR446 Radio with built-in or external Bluetooth (dongle).
The pairing procedure must be done using the "Volume +" or the "Volume -" buttons.
› Pairing to the "Volume +" button: for Phone with music A2DP stereo, GPS Naviga-
tor with A2DP audio or external mono/Stereo A2DP dongle.
› All devices paired to "Volume +" button have higher priority and will interrupt all the
other communications (like Intercom, FM Radio and Music).
› Pairing to the "Volume -" button: for a second phone with mono audio (Hands Free
Protocol) for GPS navigators/ Radar detector and other devices with mono audio.
MONO
› Phone (HFP Mono)
› GPS mono
› PMR446 Transceiver
When a device is paired to the "Vol +" or "Vol –" buttons the "Phone" mode is activated.
Attention: A2DP audio source are supported only on Vol+. The second phone paired on Vol-
can support only mono audio (HFP).
www.midlandeurope.com
MONO and STEREO
› Phone (HFP/A2DP Stereo)
› GPS (HFP/A2DP Stereo)
› Dongle (HFP/A2DP Stereo)

Background feature

It is possible to keep always in background the audio connection of the device paired
on "Vol-" button. In this way the Intercom communication will not be interrupted, for
example, by the GPS's street indication or or other audio mono device. To activate the
"Background" feature just press long the "Vol-" button, the voice "Background ON"
will tell you that now is active.
To deactivate the "Background" feature just press again long the "Vol-" button, the
voice "Background disable" will tell you that now is not active anymore.
By default the "Background" feature is off.

Pairing with one or two phones

The cellular phone can be paired to the "Vol +" (if the support for stereo A2DP is re-
quested) or to the "Vol –".
When a phone is paired to the "Vol +" or "Vol-" the "Phone" mode is activated.
An incoming call has always the higher priority, that means all other communications
will be closed (Intercom, FM Radio, Music).
If another incoming call will arrive on the second phone, an alert sound will notify it.
How to pair the Midland BTX2 PRO to a Phone
To pair the Midland BTX2 PRO to a Phone, you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on per-
manently.
3. Now press for 3 seconds the "Volume +" or "Volume -" button, the Blue and Red
light will flash.
4. Enable the Bluetooth device search feature on your mobile phone
5. After some seconds, "Midland BTX2 PRO" will be displayed on your mobile phone.
Follow the pairing procedure of your Phone. If a pin code is requested you must
enter "0000" (four time zero).
When successfully paired, the Blue light of the unit will be on for one second and then
the unit will exit the setup mode and switch to the working mode (the Blue light will
start flashing).
You can use now your Midland BTX2 PRO together with the Phone.
How to use a Phone
After pairing your phone to the Midland BTX2 PRO unit you must switch to the "Pho-
9