Using Your Cleaner; Cleaner Maintenance - Hoover Space Explorer SL71 SL10011 Manuel D'utilisation

GETTING TO KNOW YOUR CLEANER
A. Cleaner Main Body
B. On/Off Pedal
C. Hose Latch for Nano Pack™ system
D. Cord Reel Pedal
E. Bag Check Indicator
F. Bag Door Release Button
G. Hose Release Button
H. Hose
I. Hose Handle Hook (For Nano Pack™
system)
J. Hose Handle
K. Suction Regulator
L. Telescopic Tube
M. Telescopic Tube Adjuster
N. Telescopic Tube Parking Hook (For
Nano Pack™ system)
ASSEMBLYING YOUR CLEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it clips and locks into position.
To release: simply press the buttons on the hose end and pull. [1]
2. Connect the hose handle to the telescopic tube upper end [2], or accessories if
required.
3. Connect the telescopic tube lower end to the carpet and floor nozzle** [3] or
accessories, if required.

USING YOUR CLEANER

1. Extract power cord and plug it into the power supply. [4] Do not pull the cord beyond
the red marker.
2. Adjust the telescopic tube to the desired height by moving the telescopic tube
adjuster to the most comfortable cleaning position. [5]
3. Carpet & Floor Nozzle **. Press the floor type selector* on the nozzle [6] to select
the ideal cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
O. Carpet and Floor nozzle (GP)**
O1. Carpet Nozzle (CA)**
O2. Hard Floor Nozzle (HF)**
P. Floor Type Selector*
Q. 2 in 1 accessory
R. Exhaust Filter Cover Release Button
S. Nozzle Parking Slot
T. Telescopic Tube Parking Slot
U. Pre-motor Filter
V. Exhaust Filter
W. Pet Hair Remover Mini Turbo Nozzle*
X. Allergen Remover Mini Turbo Nozzle*
Y. Grand Turbo Nozzle*
Z. Parquet Nozzle*
Z1. Parquet Extra Nozzle*
Z2. Parquet Nozzle*
4. Switch the cleaner on by pressing the On/Off Pedal on the cleaner main body. [7]
5. Adjust the Suction Regulator on the hose handle to the desired level. [8]
6. Switch off at the end of use by pressing the On/Off Pedal. Unplug and press the cord reel
pedal to wind the power cord back into the cleaner. [9]
PARKING AND STORAGE SECTION
The flexible hose and telescopic tube can be parked for temporary while in use [10]
or in the Nano Pack™ storage position when not in use:
Retract the telescopic tube to its storage length. [13]
1.
2. Remove the nozzle from the end of the telescopic tube.
3. Remove the hose handle from the telescopic tube.
4. Lift the Hose Latch at the rear of the cleaner and wrap the flexible hose around the
product. [13]
5. Place the nozzle into the nozzle parking slot underneath the product. [13]
6. Place the telescopic tube into the telescopic tube parking slot underneath the
product. [13]

CLEANER MAINTENANCE

Replacing the Dust Bag
If the bag check indicator is red, please check and, if necessary, replace the bag.
1. Remove the hose from the cleaner.
Press the Bag Door Release Button to open the bag door. [14]
2.
Close the bag to avoid dust escaping by pulling the tongue and remove the bag. [15]
3.
Carefully dispose the full bag into a bin. [16]
4. Fit a new bag into the cleaner by inserting the collar into the bag holder. [16]
5. Close the Bag door.
REMEMBER: The bag check indicator may be red if an obstruction has occurred. In this case
refer to 'Removing a Blockage From the System'.
Cleaning the Filter:
To maintain optimum performance of your cleaner, please wash the pre-motor filter and
exhaust filter after each 5 bag changes.
To remove the pre-motor filter:
1. Open the bag door and remove the dust bag from the cleaner (see "Replacing The
dust bag").
2. To remove the pre-motor filter slide the pre-motor filter frame from the cleaner. [17]
3. Remove the filter from the holder. [17]
Cleaning the exhaust filter:
Open the exhaust filter cover by pressing the release button. [18]
1.
2
*Certain Models Only
GB
**Nozzle design may vary according to models