Publicité
Les langues disponibles
Les langues disponibles
Burner ports: Check burner flames occasionally
for proper size
and shape as shown above. A good flame is blue in color, not
yellow. Keep this area free of soil and do not allow spills, food,
cleaning agents or any other material to enter the burner ports.
To Clean:
1. Remove the burner cap from the burner base and clean
according to "General Cleaning" section.
2. Clean the gas tube opening with a damp cloth.
3. Clean clogged burner ports with a straight pin as shown. Do
not enlarge or distort the port. Do not use a wooden
toothpick.
If the burner needs to be adjusted, contact a
trained repair specialist.
f
4=
Replace the burner cap, making sure the alignment pins on
the cap are properly aligned with the burner base.
5=
1. Incorrect
2. Correct
Turn on the burner. If the burner does not light, check cap
alignment. If the burner still does not light, do not service the
sealed burner yourself. Contact a trained repair specialist.
Rough finishes may scratch the cooktop. Aluminum
and copper
may be used as a core or base in cookware. However, when used
as a base it can leave permanent marks on the cooktop or grates.
Cookware material is a factor in how quickly and evenly heat is
transferred, which affects cooking results. A nonstick finish has
the same characteristics
as its base material. For example,
aluminum cookware with a nonstick finish will take on the
properties of aluminum.
Use the following chart as a guide for cookware material
characteristics.
COOKWARE
CHARACTERISTICS
Aluminum
Cast iron
•
Heats quickly and evenly.
•
Suitable for all types of cooking.
•
Medium or heavy thickness is best for
most cooking tasks.
•
Heats slowly and evenly.
•
Good for browning and frying.
•
Maintains heat for slow cooking.
Ceramic or
•
Follow manufacturer's
instructions.
Ceramic glass
•
Heats slowly, but unevenly.
•
Ideal results on low to medium heat
settings.
Copper
•
Heats very quickly and evenly.
Earthenware
•
Follow manufacturer's
instructions.
•
Use on low heat settings.
Porcelain enamel-
•
See stainless steel or cast iron.
on-steel
or cast
iron
Stainless steel
•
Heats quickly, but unevenly.
•
A core or base of aluminum or copper on
stainless steel provides even heating.
When canning for long periods, alternate the use of surface
cooking areas, elements or surface burners between batches.
This allows time for the most recently used areas to cool.
•
Center the canner on the grate or largest surface cooking
area or element. Canners should not extend more than 1 in.
(2.5 cm) outside the cooking area.
•
Do not place canner on two surface cooking areas, elements
or surface burners at the same time.
•
On ceramic glass models, use only flat-bottomed
canners.
•
On coil element models, the installation of a Canning Unit Kit
is recommended.
If a kit is not installed, the life of the coil
element will be shortened. See "Assistance
or Service" for
ordering instructions.
•
For more information, contact your local U.S. Government
Agricultural Department Extension Office. In Canada, contact
Agriculture Canada. Companies that manufacture
home
canning products can also offer assistance.
IMPORTANT: Never leave empty cookware on a hot surface
cooking area, element or surface burner.
Ideal cookware should have a flat bottom, straight sides, a well-
fitting lid and the material should be of medium-to-heavy
thickness.
ELECTRONICOVEN
CONTROLS
Style 1 Electronic Oven Controls (on some models)
1
2
3
4
6
7
8
9
10
11
12
1. Display
8. Warming Drawer
2. Timer
(on some models)
3. Clock
9. Temperature
4. Auto Clean
10. Timed Cooking
5. Oven Light Pad (on some
(on some models)
models)
11. Hour/Minute
6. Sequence Programming
(on some models)
(on some models)
12. Start/Control
Lock
7. Qven Settings
13. Qff/Cancel
13
Publicité
