Pioneer DJM-900NXS Mode D'emploi page 18

, buttons (param- Use these to set the cycle for moving the cut-off frequency as a
BEAT
eter 1) time of 1/4 – 64/1 with respect to the time of one beat of the BPM.
Use this to set the cycle at which the cut-off frequency is moved.
TIME control (parameter 2)
10 to 32000 (ms)
LEVEL/DEPTH control The further the control is turned clockwise, the more the effect
(parameter 3) is stressed.
The cycle at which the cut-off frequency is moved fluctuates
X-PAD (parameter 4)
finely.
FLANGER 1
A 1-cycle flanger effect is produced according to the beat fraction set with the [BEAT
, ] buttons.
Short delay
Cycle
, buttons (param- Use these to set the 1/4 – 64/1 effect time with respect to the
BEAT
eter 1) time of one beat of the BPM.
Use this to set the cycle by which the flanger effect moves.
TIME control (parameter 2)
10 to 32000 (ms)
The further the control is turned clockwise, the more the effect
LEVEL/DEPTH control is stressed.
(parameter 3) When turned all the way counterclockwise, only the original
sound is output.
X-PAD (parameter 4) The cycle at which the flanger effect is moved fluctuates finely.
PHASER
1
The phaser effect changes according to the beat fraction set with the [BEAT
buttons.
Phase shift
Cycle
, buttons (param- Use these to set the cycle for moving the phaser effect as of time
BEAT
eter 1) of 1/4 – 64/1 with respect to the time of one beat of the BPM.
This sets the cycle by which the phaser effect is moved.
TIME control (parameter 2)
10 to 32000 (ms)
The further the control is turned clockwise, the more the effect
LEVEL/DEPTH control is stressed.
(parameter 3) When turned all the way counterclockwise, only the original
sound is output.
X-PAD (parameter 4) The cycle at which the phaser effect is moved fluctuates finely.
ROBOT
1
The original sound is changed to a sound like one produced by a robot.
, buttons (param- Use these to set the degree of the effect sound, from -100 –
BEAT
eter 1) 100 %.
Use this to set the degree of the effect sound.
TIME control (parameter 2)
-100–100 (%)
LEVEL/DEPTH control Sets the balance between the original sound and the effect
(parameter 3) sound.
X-PAD (parameter 4) This changes the degree of the effect sound.
MELODIC
1 2
The mid-range of the sound being input at the point when the [ON/OFF] button is
pressed is recorded, and the recorded sound is output according to the level of the
sound being input.
, buttons (param-
BEAT
This sets the way in which the recorded sound is played.
eter 1)
TIME control (parameter 2) This sets the way in which the recorded sound is played.
18
En
Frequency
Time
,
Time
LEVEL/DEPTH control
(parameter 3)
X-PAD (parameter 4)
SLIP ROLL
1 2
The sound being input at the point when the [ON/OFF] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[BEAT , ] buttons.
When the effect time changes, the input sound is recorded again.
Original
Changed from 1/2
Effect turned on
to 1/1
Roll
1/2 repeat
, buttons (param-
BEAT
eter 1)
TIME control (parameter 2)
LEVEL/DEPTH control
(parameter 3)
X-PAD (parameter 4)
ROLL 1 2
The sound being input at the point when the [ON/OFF] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[BEAT , ] buttons.
Original
Effect turned on
]
1/1 roll
Repeated
, buttons (param-
BEAT
eter 1)
TIME control (parameter 2)
LEVEL/DEPTH control
(parameter 3)
X-PAD (parameter 4)
REV ROLL 1 2
The sound being input at the point when the [ON/OFF] button is pressed is
recorded, and the recorded sound is reversed then output repeatedly according to
the beat fraction set with the [BEAT
Original
Effect turned on
1/1 reverse
roll
Reversed and repeated
, buttons (param-
BEAT
eter 1)
TIME control (parameter 2)
LEVEL/DEPTH control
(parameter 3)
X-PAD (parameter 4)
SND/RTN (MIDI LFO)
Connect an external effector, etc., here.
This sets the balance between the original sound and the
recorded sound.
This sets the way in which the recorded sound is played.
1/1 repeat
Use these to set an effect time of 1/16 – 16/1 with respect to the
time of one beat of the BPM.
Use this to set the effect time.
10 to 4000 (ms)
Use this to set the balance between the original sound and ROLL.
Use this to set the effect time.
Use these to set an effect time of 1/16 – 16/1 with respect to the
time of one beat of the BPM.
Use this to set the effect time.
10 to 4000 (ms)
Use this to set the balance between the original sound and ROLL.
Use this to set the effect time.
, ] buttons.
Use these to set an effect time of 1/16 – 16/1 with respect to the
time of one beat of the BPM.
Use this to set the effect time.
10 to 4000 (ms)
Use this to set the balance between the original sound and ROLL.
Use this to set the effect time.