Technical Data; Before Putting The Machine Into Operation - EINHELL PTK 800 Mode D'emploi

Anleitung PTK 800 SPK 1
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved."

5. Technical data

Asynchronous motor 230 V 50 Hz
Power rating 800 W S2 30 min 580 W S1
Idle speed n 0
Carbide saw blade 200 x 16 x 2.4 mm
Number of teeth
Table size 500 x 335 mm
Cutting height max.90°
Cutting height max.45°
Connector for dust extractor dia. 35 mm
Size, complete 500 x 335 x 240 mm
Weight
Load factor:
A load factor of S2 30 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (800 W)
for no longer than the time stipulated on the
specifications label (30 minutes ON period).
If you fail to observe this time limit the motor will
overheat. During the OFF period the motor will
cool again to its starting temperature.
6. Before putting the machine into
operation
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong stand.
All the covers and safety devices have to be
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
Before you connect the machine to the power
12.04.2005 10:08 Uhr Seite 15
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
Always pull out the power plug before carrying
out any maintenance or conversion work.
7.1 Fitting the saw blade (Fig. 2/3)
Caution! Pull out the power plug.
Slacken the chip bin cover (19) by undoing the
fixing screws (20) and swing it up.
Undo the nut (21) with a ring wrench (30) on the
nut (21) and a face wrench (31) on the outer
2950 rpm
flange (22) to apply counter-pressure.
Caution! Turn the nut in the direction of rotation
20 of the saw blade (4).
Take off the outer flange (22) and pull the old
saw blade (4) off the inner flange by dropping the
35 mm blade at an angle.
Clean the mounting flange.
35 mm
Fit the new saw blade in reverse order.
Caution! Note the direction of rotation (see arrow
on the saw blade).
14 kg
7.2 Adjusting the splitter (Fig. 4-6)
Remove the saw blade guard (2) (see 7.3).
Take out the table insert (6) (see 7.4).
Slacken the two hexagon socket-head screws
(24).
Adjust the splitter (5) so that the gap between the
saw blade (4) and the splitter (5) equals 3 - 5 mm
(see Fig. 6)
The splitter (5) has to be in line with the saw
blade (4) in longitudinal direction.
Retighten the two screws (24).
The setting of the splitter has to be checked each
time after changing the saw blade.
7.3 Fitting the saw blade guard (Fig. 4)
Mount the saw blade guard (2) on the splitter (5)
and align.
Insert the knurled screw (18) through the hole in
the saw blade guard (2) and in the splitter (5)
and secure it with the nut.
To remove the saw blade guard, proceed in
reverse order.
7.4 Replacing the table insert (Fig. 4)
Caution! Pull out the power plug.
Remove the 6 screws (23).
Take off the saw blade guard (2) (see 7.3).
GB
15