Dust/Chip Extraction; Starting Operation - Bosch AdvancedMulti 18 Notice Originale

22 | English
Sanding sheet Material
– Paint
– Varnish
– Filler
– Bodyfiller
White quality
Attaching/changing the sanding sheet on the sanding
plate
The sanding plate (13) is fitted with a hook-and-loop fasten-
ing, allowing sanding sheets with a hook-and-loop backing to
be secured quickly and easily.
Tap the hook-and-loop fastening of the sanding plate (13)
before fitting the sanding sheet (14) to facilitate maximum
adhesion.
Position the sanding sheet (14) so that it is flush with one
side of the sanding plate (13), then place the sanding sheet
on the sanding plate and press it on firmly.
To ensure optimum dust extraction, make sure that the
punched holes in the sanding sheet are aligned with the
drilled holes in the sanding plate.
To remove the sanding sheet (14), take hold of it by a corner
and pull it away from the sanding plate (13).
You can use all sanding sheets, polishing and cleaning
fleeces from the Delta 93 mm series in Bosch's range of ac-
cessories.
Sanding accessories such as fleece/polishing felt are at-
tached to the sanding plate in the same way.

Dust/chip extraction

The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Connecting the dust extraction system (see figure C)
The dust extraction system (20) is only designed for use
with the sanding plate (13); it serves no purpose when used
together with other application tools.
Always connect a dust extraction system for sanding.
1 609 92A 4N1 | (12.10.2018)
Application
For sanding down paint
For sanding undercoats (e.g. removing brushstrokes,
paint drips and paint runs)
For final sanding of primers prior to painting
Remove the application tool and the depth stop (15) for fit-
ting the dust extraction system (20) (accessory).
Slide the dust extraction system (20) as far as it will go over
the tool holder (10) onto the collar of the power tool. Turn
the dust extraction system to the required position (not dir-
ectly under the power tool). Push the clamping lever (21)
shut to fix the dust extraction system in position.
Plug the tool sleeve of the extraction hose (18) onto the ex-
traction outlet (19). Connect the dust extraction hose (18)
to a dust extractor (accessory).
You will find an overview of how to connect various dust ex-
tractors at the end of these operating instructions.
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Operation

Starting Operation

Inserting the battery
Use only original Bosch lithium-ion batteries with the
u
voltage stated on the type plate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Insert the charged battery (4) into the base of the power tool
until you feel it engage and it is securely locked in place.
Switching On/Off
Make sure that you are able to press the On/Off switch
u
without releasing the handle.
To switch on the power tool, slide the on/off switch (2) for-
ward so that "I" appears on the switch.
The electronic soft start limits the torque when the power
tool is switched on and increases the service life of the mo-
tor.
The Constant Electronic keeps the orbital stroke rate at no
load and under load virtually consistent, guaranteeing uni-
form performance.
To switch off the power tool, slide the on/off switch (2)
backwards so that "0" appears on the switch.
Note: If the power tool shuts down automatically because
the battery is flat or overheated, switch the power tool off
Grit
Coarse 40
60
Medium 80
100
120
Fine 180
240
320
Bosch Power Tools