Technical Data; Approved Bar And Chain Combinations - Makita DCS34 Manuel D'emploi Et De Sécurité

Technical data

Single-cylinder two-stroke
Piston displacement
Cylinder bore
Piston stroke
Max. power at speed
Max. torque at speed
Idling speed
Sound Pressure Level at the operator's ear
at full load according to ANSI B 75.
Sound Pressure Level at the bystander's position
(50ft/5 m distance) according to ANSI B 75.
Ignition system
Electronic, without breaker
Spark plug
or Spark plug
Electrode gap
Fuel system
Carburetor (for Canada)
Carburetor (for USA)
(all position diaphragm carburetor
with integral fuel pump)
Fuel tank capacity
Fuel mixture
Weight
without cutting attachment
Cutting attachment
Guide bar
Cutting length
Safety saw chain (pitch) 3/8"
Drive link gauge
Chain sprocket
Chain lubrication
Oil tank capacity

Approved bar and chain combinations

"Low-kickback saw chain is a chain which has met
the kickback performance requirements of ANSI B
75. (American National Standard for Power Tools-
Gasoline-Powered Chain Saws-Safety Requirements)
when tested on the representative sample of chain
saws below 3.8. C.l.D. specifed in ANSI B 75.. The
approved bar and chain combinations are low kickback
chains according to ANSI B 75. and also meet the
kickback requirements of CSA Z62.3 for chain saws
below 80 cm .
3
The chain saw DCS34 and 4610 has been approved
with following guide bar and chain combinations:
Drive link gauge .050"
Guide bar 3/8"
length Part no.
4" (35 cm) 442 035 66
6" (40 cm) 442 040 66
"There may be other replacement bar and chain combi-
nations available that also reduces the risk of injury
from kickback".
8
1.3 / 9,000 kW/rpm
1.7 / 6,500 Nm/rpm
ZAMA with limiter caps
ZAMA with limiter caps
0 lbs. 5 oz. (4.7 kg)
4" (35 cm) • 6" (40 cm)
fully automatic oil pump
Saw chain 3/8"
Part no.
528 092 652
528 092 656
DCS34
2.0 cu. in (33 cm )
3
.45" (37 mm)
.22" (3 mm)
2,800 rpm
98 db(A)
73 db(A)
NGK BPMR 7A
.020" (0.5 mm)
3.0 oz. (0.37 l)
see chapter "Fuel"
sprocket nose bar
(528 092 ...)
.050"
6 teeth
8.8 oz. (0.25 l)
WARNING
Do not use other replacement bars and chains
unless they have been designated as meeting
the ANSI B 75. (for USA) and CSA Z62.3 (for
Canada) kickback performance requirements on
that specific powerhead, or has been designated
as "low kickback" saw chain in accordance with
the ANSI B 75. (for USA) and CSA Z62.3 (for
Canada) standard.
DCS4610
2.75 cu. in (45. cm )
3
.69" (43 mm)
.22" (3 mm)
1.7 / 9,000 kW/rpm
2.4 / 6,500 Nm/rpm
2,600 rpm
99. db(A)
76. db(A)
NGK BPMR 7A
.020" (0.5 mm)
ZAMA with limiter caps
ZAMA with limiter caps
3.0 oz. (0.37 l)
see chapter "Fuel"
0 lbs. 7 oz. (4.75 kg)
sprocket nose bar
4" (35 cm) • 6" (40 cm)
(528 092 ...)
.050"
6 teeth
fully automatic oil pump
8.8 oz. (0.25 l)